Showing 1–50 of 92 results for author: Borghesi, M

Demonstration of a cryogenic, switchable electron source for low-temperature detector calibration

Authors: D. A. Bennett, M. Borghesi, P. Campana, R. Carobene, A. Cattaneo, M. De Gerone, M. Faverzani, L. Ferrari Barusso, E. Ferri, S. Gamba, A. Giachero, M. Gobbo, D. Labranca, J. Mates, R. Moretti, A. Nucciotti, L. Origo, D. R. Schmidt, D. S. Swetz, J. N. Ullom

Abstract: We present the realization of a prototype of a compact, switchable electron source operating at cryogenic temperatures, demonstrated at energies ranging from 100 eV to 300 eV, and conceptually extendable to an arbitrary energy range. The electrons are produced via photoelectric emission, induced by a LED illuminating two 400~nm-thick commercial aluminum layers inside a cryostat, and are subsequent… ▽ More We present the realization of a prototype of a compact, switchable electron source operating at cryogenic temperatures, demonstrated at energies ranging from 100 eV to 300 eV, and conceptually extendable to an arbitrary energy range. The electrons are produced via photoelectric emission, induced by a LED illuminating two 400~nm-thick commercial aluminum layers inside a cryostat, and are subsequently accelerated by a voltage of up to 300~V. Detection is carried out with an array of transition-edge sensor (TES) microcalorimeters designed for X-ray detectors, where we successfully observe signals consistent with electrons produced at the source at rates of $\gtrsim$1~Hz and with an efficiency of $\gtrsim 10^{-14}\ e^-/γ$. One of the potential applications of this prototype is the development of a calibration method for cryogenic detectors, based on the generation, acceleration, and multiplication of electrons, followed by their conversion into high-energy photons. △ Less

Submitted 23 July, 2026; v1 submitted 22 July, 2026; originally announced July 2026.

Comments: for submission to EPJ Plus

Final assessment of radioactive impurities in the JUNO detector

Authors: Thomas Adam, Fengpeng An, Costas Andreopoulos, Giuseppe Andronico, Nikolay Anfimov, Vito Antonelli, Tatiana Antoshkina, João Pedro Athayde Marcondes de André, Didier Auguste, Nikita Balashov, Andrea Barresi, Davide Basilico, Eric Baussan, Marco Beretta, Antonio Bergnoli, Nikita Bessonov, Daniel Bick, Lukas Bieger, Svetlana Biktemerova, Thilo Birkenfeld, Simon Blyth, Manuel Böhles, Anastasia Bolshakova, Mathieu Bongrand, Matteo Borghesi , et al. (549 additional authors not shown)

Abstract: The Jiangmen Underground Neutrino Observatory (JUNO) collaboration has completed the construction of the 20,000-ton liquid scintillator detector and the associated muon veto detector system. To meet the physics objectives, the materials used in the detector must exhibit low radioactive contamination. The single-event rate in the fiducial volume (R $<$ 17.2 m) of the scintillator is required to be… ▽ More The Jiangmen Underground Neutrino Observatory (JUNO) collaboration has completed the construction of the 20,000-ton liquid scintillator detector and the associated muon veto detector system. To meet the physics objectives, the materials used in the detector must exhibit low radioactive contamination. The single-event rate in the fiducial volume (R $<$ 17.2 m) of the scintillator is required to be approximately 7 Hz for energies above 0.7 MeV, resulting in an accidental coincidence background of about 1 event per day for reactor neutrino physics analyses. Since the beginning of the construction phase, we have screened the natural radioactivity content of thousands of materials, to select those that meet the design background budget. The radioactive impurity concentrations of the materials ultimately used in the JUNO detector are summarized in this paper. The construction of the entire detector and the subsequent filling of the liquid scintillator were completed in August 2025. From the initial data, the total count rate of natural radioactivity within the detector's fiducial volume has met the requirements and is sufficient to support the reactor antineutrino analysis. △ Less

Submitted 19 July, 2026; originally announced July 2026.

Ultra-trace analysis of 40K in organic liquid scintillators

Authors: A. Barresi, D. Chiesa, D. Merli, M. Nastasi, S. Nisi, E. Previtali, M. Sisti, M. Borghesi, A. Cammi, C. Coletta, G. Ferrante, L. Loi, G. Andronico, V. Antonelli, D. Basilico, M. Beretta, A. Bergnoli, A. Brigatti, R. Brugnera, R. Bruno, A. Budano, B. Caccianiga, A. Caslini, V. Cerrone, R. Caruso , et al. (42 additional authors not shown)

Abstract: Rare-event searches require exceptionally low background levels, motivating the development of increasingly sophisticated screening methods to push sensitivity limits. Liquid scintillators are particularly attractive detector media due to their intrinsic radiopurity and the ability to scale to large target masses. In this work, we present a screening strategy capable of measuring ultra-trace conce… ▽ More Rare-event searches require exceptionally low background levels, motivating the development of increasingly sophisticated screening methods to push sensitivity limits. Liquid scintillators are particularly attractive detector media due to their intrinsic radiopurity and the ability to scale to large target masses. In this work, we present a screening strategy capable of measuring ultra-trace concentrations of $^{40}\text{K}$ with sensitivities below $10^{-15}$g/g. The method combines neutron activation analysis with a dedicated radiochemical treatment, followed by low-background HPGe gamma spectroscopy. Using this approach, we achieved a minimum detectable concentration of $2.9\cdot10^{-16}$g/g for $^{40}\text{K}$, placing this technique among the most sensitive currently available. △ Less

Submitted 8 July, 2026; originally announced July 2026.

Embedded underwater front-end electronics for the 3-inch photomultipliers in the JUNO experiment

Authors: Cédric Cerna, Miao He, Xiaoshan Jiang, Juan Pedro Ochoa-Ricoux, Frédéric Perrot, Angel Abusleme, Thomas Adam, Fengpeng An, Costas Andreopoulos, Giuseppe Andronico, João Pedro Athayde Marcondes de André, Nikolay Anfimov, Vito Antonelli, Tatiana Antoshkina, Didier Auguste, Nikita Balashov, Andrea Barresi, Davide Basilico, Eric Baussan, Marco Beretta, Antonio Bergnoli, Nikita Bessonov, Daniel Bick, Lukas Bieger, Svetlana Biktemerova , et al. (576 additional authors not shown)

Abstract: The Jiangmen Underground Neutrino Observatory (JUNO) is a 20-kton liquid scintillator-based, low-radioactivity, multi-purpose neutrino detector located 693 meters (1800 m.w.e.) underground in the Guangdong province, China. To detect scintillation light produced in the target, the detector is equipped with 17,612 20-inch photomultipliers (PMTs), forming the Large PMT system (LPMT). In addition, 25,… ▽ More The Jiangmen Underground Neutrino Observatory (JUNO) is a 20-kton liquid scintillator-based, low-radioactivity, multi-purpose neutrino detector located 693 meters (1800 m.w.e.) underground in the Guangdong province, China. To detect scintillation light produced in the target, the detector is equipped with 17,612 20-inch photomultipliers (PMTs), forming the Large PMT system (LPMT). In addition, 25,600 3-inch photomultipliers (the Small Photomultiplier System or SPMT) are deployed in the gaps between the LPMTs. This paper presents the design and performance of the underwater front-end electronics developed for the SPMT system. It details the individual electronics boards and their key components, the inter-board interfaces, the system-level design, and the firmware architecture that supports data acquisition and control. It also outlines mechanical and thermal integration, board validation procedures, and system performance metrics. The readout chain includes digitization of 128 PMT channels per unit, synchronized time-stamping, charge measurement, event packaging, and bandwidth management. Comprehensive validation confirms the system's readiness to meet JUNO's stringent physics goals. The underwater electronics achieve noise levels as low as 0.04 photoelectrons with minimal crosstalk (below 0.4%) and a bandwidth of 57 MB/s, ensuring reliable single photo-electron detection and operation under high-rate conditions. The SPMT system has now been fully integrated and installed in JUNO. Its commissioning and physics performance will be reported in a future publication. △ Less

Submitted 1 June, 2026; v1 submitted 28 April, 2026; originally announced April 2026.

Comments: Submitted to Nucl. Instrum. Methods Phys. Res. A

Real-Time Wiener Deconvolution for feature reconstruction in JUNO

Authors: L. Lastrucci, M. Grassi, A. Triossi, J. Hu, X. Jiang, R. Brugnera, A. Garfagnini, V. Cerrone, L. V. D'Auria, A. Gavrikov, R. M. Guizzetti, A. Serafini, G. Andronico, V. Antonelli, A. Barresi, D. Basilico, M. Beretta, A. Bergnoli, M. Borghesi, A. Brigatti, R. Bruno, A. Budano, B. Caccianiga, A. Cammi, R. Caruso , et al. (52 additional authors not shown)

Abstract: In particle physics, experiments generate substantial amounts of data that can be difficult to process without preliminary scaling. To avoid losing potentially crucial data, experimental collaborations are studying novel techniques for real-time data processing to extract features for further physics analysis. A common approach, especially in neutrino physics, is to use FPGAs for data acquisition… ▽ More In particle physics, experiments generate substantial amounts of data that can be difficult to process without preliminary scaling. To avoid losing potentially crucial data, experimental collaborations are studying novel techniques for real-time data processing to extract features for further physics analysis. A common approach, especially in neutrino physics, is to use FPGAs for data acquisition and pre-processing. This paper presents an advanced Real-Time Wiener deconvolution algorithm designed to leverage the processing capabilities of the FPGA integrated into the readout boards of the Jiangmen Underground Neutrino Observatory (JUNO). The goal is to enable real-time reconstruction of the signal generated by photomultiplier tubes (PMTs) when neutrino interactions are detected. By exploiting online reconstruction of the signal generated by PMTs, we expect to improve the detection of low-energy depositions, such as those produced by transient astrophysical phenomena. These depositions are usually not saved because of the significant background that affects the low end of the energy spectrum, which would result in a large trigger rate, hence a large amount of data required for storage. This paper presents the features of the algorithm, including its ability to manage high-throughput data streams with minimal latency, adaptability, and resilience in discerning the characteristics of input data. Performance is evaluated on a JUNO electronic board. This study further demonstrates the potential of FPGA-based solutions for neutrino physics. △ Less

Submitted 26 March, 2026; originally announced March 2026.

Ultra-trace analysis of U and Th in organic liquid scintillators with high sensitivity

Authors: A. Barresi, D. Chiesa, D. Merli, M. Nastasi, S. Nisi, E. Previtali, M. Sisti, M. Borghesi, A. Cammi, C. Coletta, G. Ferrante, L. Loi, G. Andronico, V. Antonelli, D. Basilico, M. Beretta, A. Bergnoli, A. Brigatti, R. Brugnera, R. Bruno, A. Budano, B. Caccianiga, V. Cerrone, R. Caruso, C. Clementi , et al. (41 additional authors not shown)

Abstract: Rare event searches demand extremely low background levels, necessitating ever-advancing screening techniques to enhance sensitivity. Liquid scintillators are highly attractive as detector media due to their inherent radiopurity and scalability in mass. In this work, we present a screening procedure to measure ultra-trace concentrations of natural contaminants -- $^{238}$U and $^{232}$Th -- with s… ▽ More Rare event searches demand extremely low background levels, necessitating ever-advancing screening techniques to enhance sensitivity. Liquid scintillators are highly attractive as detector media due to their inherent radiopurity and scalability in mass. In this work, we present a screening procedure to measure ultra-trace concentrations of natural contaminants -- $^{238}$U and $^{232}$Th -- with sensitivities at the \qty{E-15}{g/g} level. Our method combines neutron activation analysis with radiochemical techniques, followed by \bg\ coincidence spectroscopy to minimize interference backgrounds. This approach achieves sensitivities of \qty{0.65E-15}{g/g} for $^{238}$U and \qty{2.3E-15}{g/g} for $^{232}$Th, among the best reported worldwide. Potential pathways for further sensitivity improvements are outlined in the conclusions. △ Less

Submitted 6 December, 2025; originally announced December 2025.

Initial performance results of the JUNO detector

Authors: Angel Abusleme, Thomas Adam, Kai Adamowicz, David Adey, Shakeel Ahmad, Rizwan Ahmed, Timo Ahola, Sebastiano Aiello, Fengpeng An, Guangpeng An, Costas Andreopoulos, Giuseppe Andronico, João Pedro Athayde Marcondes de André, Nikolay Anfimov, Vito Antonelli, Tatiana Antoshkina, Burin Asavapibhop, Didier Auguste, Margherita Buizza Avanzini, Andrej Babic, Jingzhi Bai, Weidong Bai, Nikita Balashov, Roberto Barbera, Andrea Barresi , et al. (1114 additional authors not shown)

Abstract: The Jiangmen Underground Neutrino Observatory (JUNO) started physics data taking on 26 August 2025. JUNO consists of a 20-kton liquid scintillator central detector, surrounded by a 35 kton water pool serving as a Cherenkov veto, and almost 1000 m$^2$ of plastic scintillator veto on top. The detector is located in a shallow underground laboratory with an overburden of 1800 m.w.e. This paper present… ▽ More The Jiangmen Underground Neutrino Observatory (JUNO) started physics data taking on 26 August 2025. JUNO consists of a 20-kton liquid scintillator central detector, surrounded by a 35 kton water pool serving as a Cherenkov veto, and almost 1000 m$^2$ of plastic scintillator veto on top. The detector is located in a shallow underground laboratory with an overburden of 1800 m.w.e. This paper presents the performance results of the detector, extensively studied during the commissioning of the water phase, the subsequent liquid scintillator filling phase, and the first physics runs. The liquid scintillator achieved an attenuation length of 20.6 m at 430 nm, while the high coverage PMT system and scintillator together yielded about 1785 photoelectrons per MeV of energy deposit at the detector centre, measured using the 2.223 MeV $γ$ from neutron captures on hydrogen with an Am-C calibration source. The reconstructed energy resolution is 3.4% for two 0.511 MeV $γ$ at the detector centre and 2.9% for the 0.93 MeV quenched Po-214 alpha decays from natural radioactive sources. The energy nonlinearity is calibrated to better than 1%. Intrinsic contaminations of U-238 and Th-232 in the liquid scintillator are below 10$^{-16}$ g/g, assuming secular equilibrium. The water Cherenkov detector achieves a muon detection efficiency better than 99.9% for muons traversing the liquid scintillator volume. During the initial science runs, the data acquisition duty cycle exceeded 97.8%, demonstrating the excellent stability and readiness of JUNO for high-precision neutrino physics. △ Less

Submitted 18 November, 2025; originally announced November 2025.

Comments: 38 pages, 23 figures

Prospects for geoneutrino detection with JUNO

Authors: Thomas Adam, Shakeel Ahmad, Rizwan Ahmed, Fengpeng An, João Pedro Athayde Marcondes de André, Costas Andreopoulos, Giuseppe Andronico, Nikolay Anfimov, Vito Antonelli, Tatiana Antoshkina, Didier Auguste, Marcel Büchner, Weidong Bai, Nikita Balashov, Andrea Barresi, Davide Basilico, Eric Baussan, Marco Beretta, Antonio Bergnoli, Nikita Bessonov, Daniel Bick, Lukas Bieger, Svetlana Biktemerova, Thilo Birkenfeld, Simon Blyth , et al. (605 additional authors not shown)

Abstract: Geoneutrinos, which are antineutrinos emitted during the decay of long-lived radioactive elements inside Earth, serve as a unique tool for studying the composition and heat budget of our planet. The Jiangmen Underground Neutrino Observatory (JUNO) experiment in China, which has recently completed construction, is expected to collect a sample comparable in size to the entire existing world geoneutr… ▽ More Geoneutrinos, which are antineutrinos emitted during the decay of long-lived radioactive elements inside Earth, serve as a unique tool for studying the composition and heat budget of our planet. The Jiangmen Underground Neutrino Observatory (JUNO) experiment in China, which has recently completed construction, is expected to collect a sample comparable in size to the entire existing world geoneutrino dataset in less than a year. This paper presents an updated estimation of sensitivity to geoneutrinos of JUNO using the best knowledge available to date about the experimental site, the surrounding nuclear reactors, the detector response uncertainties, and the constraints expected from the TAO satellite detector. To facilitate comparison with present and future geological models, our results cover a wide range of predicted signal strengths. Despite the significant background from reactor antineutrinos, the experiment will measure the total geoneutrino flux with a precision comparable to that of existing experiments within its first few years, ultimately achieving a world-leading precision of about 8% over ten years. The large statistics of JUNO will also allow separation of the Uranium-238 and Thorium-232 contributions with unprecedented precision, providing crucial constraints on models of formation and composition of Earth. Observation of the mantle signal above the lithospheric flux will be possible but challenging. For models with the highest predicted mantle concentrations of heat-producing elements, a 3-sigma detection over six years requires knowledge of the lithospheric flux to within 15%. Together with complementary measurements from other locations, the geoneutrino results of JUNO will offer cutting-edge, high-precision insights into the interior of Earth, of fundamental importance to both the geoscience and neutrino physics communities. △ Less

Submitted 10 November, 2025; originally announced November 2025.

Comments: 32 pages, with 13 figures and 5 tables

Design, waterproofing, and mass production of the 3-inch PMT frontend system of JUNO

Authors: Jilei Xu, Miao He, Cédric Cerna, Yongbo Huang, Thomas Adam, Shakeel Ahmad, Rizwan Ahmed, Fengpeng An, Costas Andreopoulos, Giuseppe Andronico, João Pedro Athayde Marcondes de André, Nikolay Anfimov, Vito Antonelli, Tatiana Antoshkina, Didier Auguste, Weidong Bai, Nikita Balashov, Andrea Barresi, Davide Basilico, Eric Baussan, Marco Beretta, Antonio Bergnoli, Nikita Bessonov, Daniel Bick, Lukas Bieger , et al. (609 additional authors not shown)

Abstract: Over 25,600 3-inch photomultiplier tubes (PMTs) have been instrumented for the central detector of the Jiangmen Underground Neutrino Observatory. Each PMT is equipped with a high-voltage divider and a frontend cable with waterproof sealing. Groups of sixteen PMTs are connected to the underwater frontend readout electronics via specialized multi-channel waterproof connectors. This paper outlines th… ▽ More Over 25,600 3-inch photomultiplier tubes (PMTs) have been instrumented for the central detector of the Jiangmen Underground Neutrino Observatory. Each PMT is equipped with a high-voltage divider and a frontend cable with waterproof sealing. Groups of sixteen PMTs are connected to the underwater frontend readout electronics via specialized multi-channel waterproof connectors. This paper outlines the design and mass production processes for the high-voltage divider, the cable and connector, as well as the waterproof potting of the PMT bases. The results of the acceptance tests of all the integrated PMTs are also presented. △ Less

Submitted 22 January, 2026; v1 submitted 7 October, 2025; originally announced October 2025.

Efficient ion re-acceleration in laboratory-produced interpenetrating collisionless shocks

Authors: W. Yao, I. Cohen, P. Suarez Gerona, H. Ahmed, A. F. A. Bott, S. N. Chen, M. Cook, R. Lelièvre, P. Martin, T. Waltenspiel, P. Antici, J. Béard, M. Borghesi, D. Caprioli, A. Ciardi, E. d'Humières, M. François, L. Gremillet, A. Marcowith, M. Miceli, T. Seebaruth, S. Orlando, J. Fuchs

Abstract: Although the origin of cosmic rays (CRs) remains an open question, collisionless magnetized shock waves are widely regarded as key sites for particle acceleration. Recent theories further suggest that shock-shock collisions in stellar clusters could provide the additional acceleration needed to explain the observed high-energy CR spectrum. Here, we investigate this hypothesis through a laser-based… ▽ More Although the origin of cosmic rays (CRs) remains an open question, collisionless magnetized shock waves are widely regarded as key sites for particle acceleration. Recent theories further suggest that shock-shock collisions in stellar clusters could provide the additional acceleration needed to explain the observed high-energy CR spectrum. Here, we investigate this hypothesis through a laser-based experiment that creates magnetized plasma conditions similar to astrophysical environments. Our results demonstrate that interpenetrating collisionless shocks can significantly boost the energy of ambient protons previously energized by the individual shocks, while also improving the overall acceleration efficiency. Numerical kinetic simulations corroborate these findings, revealing that protons are reaccelerated via their bouncing motion in the convective electric fields of the colliding magnetized flows. By allowing to highly energize ambient protons, our novel colliding-shock platform opens the prospect to test the long-discussed mechanism of diffusive shock acceleration in a controlled laboratory setting. △ Less

Submitted 26 June, 2026; v1 submitted 27 August, 2025; originally announced August 2025.

Characterization and automated optimization of laser-driven proton beams from converging liquid sheet jet targets

Authors: G. D. Glenn, F. Treffert, H. Ahmed, S. Astbury, M. Borghesi, N. Bourgeois, C. B. Curry, S. J. D. Dann, S. DiIorio, N. P. Dover, T. Dzelzainis, O. Ettlinger, M. Gauthier, L. Giuffrida, R. J. Gray, J. S. Green, G. S. Hicks, C. Hyland, V. Istokskaia, M. King, B. Loughran, D. Margarone, O. McCusker, P. McKenna, Z. Najmudin , et al. (9 additional authors not shown)

Abstract: Compact, stable, and versatile laser-driven ion sources hold great promise for applications ranging from medicine to materials science and fundamental physics. While single-shot sources have demonstrated favorable beam properties, including the peak fluxes necessary for several applications, high repetition rate operation will be necessary to generate and sustain the high average flux needed for m… ▽ More Compact, stable, and versatile laser-driven ion sources hold great promise for applications ranging from medicine to materials science and fundamental physics. While single-shot sources have demonstrated favorable beam properties, including the peak fluxes necessary for several applications, high repetition rate operation will be necessary to generate and sustain the high average flux needed for many of the most exciting applications of laser-driven ion sources. Further, to navigate through the high-dimensional space of laser and target parameters towards experimental optima, it is essential to develop ion acceleration platforms compatible with machine learning learning techniques and capable of autonomous real-time optimization. Here we present a multi-Hz ion acceleration platform employing a liquid sheet jet target. We characterize the laser-plasma interaction and the laser-driven proton beam across a variety of key parameters governing the interaction using an extensive suite of online diagnostics. We also demonstrate real-time, closed-loop optimization of the ion beam maximum energy by tuning the laser wavefront using a Bayesian optimization scheme. This approach increased the maximum proton energy by 11% compared to a manually-optimized wavefront by enhancing the energy concentration within the laser focal spot, demonstrating the potential for closed-loop optimization schemes to tune future ion accelerators for robust high repetition rate operation. △ Less

Submitted 8 August, 2025; originally announced August 2025.

Comments: 39 pages, 8 figures

Journal ref: Phys. Rev. Research 8, 013101 (2026)

Simulation-based inference for Precision Neutrino Physics through Neural Monte Carlo tuning

Authors: A. Gavrikov, A. Serafini, D. Dolzhikov, A. Garfagnini, M. Gonchar, M. Grassi, R. Brugnera, V. Cerrone, L. V. D'Auria, R. M. Guizzetti, L. Lastrucci, G. Andronico, V. Antonelli, A. Barresi, D. Basilico, M. Beretta, A. Bergnoli, M. Borghesi, A. Brigatti, R. Bruno, A. Budano, B. Caccianiga, A. Cammi, R. Caruso, D. Chiesa , et al. (41 additional authors not shown)

Abstract: Precise modeling of detector energy response is crucial for next-generation neutrino experiments which present computational challenges due to lack of analytical likelihoods. We propose a solution using neural likelihood estimation within the simulation-based inference framework. We develop two complementary neural density estimators that model likelihoods of calibration data: conditional normaliz… ▽ More Precise modeling of detector energy response is crucial for next-generation neutrino experiments which present computational challenges due to lack of analytical likelihoods. We propose a solution using neural likelihood estimation within the simulation-based inference framework. We develop two complementary neural density estimators that model likelihoods of calibration data: conditional normalizing flows and a transformer-based regressor. We adopt JUNO - a large neutrino experiment - as a case study. The energy response of JUNO depends on several parameters, all of which should be tuned, given their non-linear behavior and strong correlations in the calibration data. To this end, we integrate the modeled likelihoods with Bayesian nested sampling for parameter inference, achieving uncertainties limited only by statistics with near-zero systematic biases. The normalizing flows model enables unbinned likelihood analysis, while the transformer provides an efficient binned alternative. By providing both options, our framework offers flexibility to choose the most appropriate method for specific needs. Finally, our approach establishes a template for similar applications across experimental neutrino and broader particle physics. △ Less

Submitted 31 July, 2025; originally announced July 2025.

Phenomenological Modeling of the $^{163}$Ho Calorimetric Electron Capture Spectrum from the HOLMES Experiment

Authors: F. Ahrens, B. K. Alpert, D. T. Becker, D. A. Bennett, E. Bogoni, M. Borghesi, P. Campana, R. Carobene, A. Cattaneo, A. Cian, H. A. Corti, N. Crescini, M. De Gerone, W. B. Doriese, M. Faverzani, L. Ferrari Barusso, E. Ferri, J. Fowler, G. Gallucci, S. Gamba, J. D. Gard, H. Garrone, F. Gatti, A. Giachero, M. Gobbo , et al. (24 additional authors not shown)

Abstract: We present a comprehensive phenomenological analysis of the calorimetric electron capture (EC) decay spectrum of $^{163}$Ho as measured by the HOLMES experiment. Using high-statistics data, we unfold the instrumental energy resolution from the measured spectrum and model it as a sum of Breit-Wigner resonances and shake-off continua, providing a complete set of parameters for each component. Our ap… ▽ More We present a comprehensive phenomenological analysis of the calorimetric electron capture (EC) decay spectrum of $^{163}$Ho as measured by the HOLMES experiment. Using high-statistics data, we unfold the instrumental energy resolution from the measured spectrum and model it as a sum of Breit-Wigner resonances and shake-off continua, providing a complete set of parameters for each component. Our approach enables the identification and tentative interpretation of all observed spectral features, including weak and overlapping structures, in terms of atomic de-excitation processes. We compare our phenomenological model with recent ab initio theoretical calculations, finding good agreement for both the main peaks and the spectral tails, despite the limitations of current theoretical and experimental precision. The model delivers an accurate description of the endpoint region, which is crucial for neutrino mass determination, and allows for a realistic treatment of backgrounds such as pile-up and tails of low-energy components. Furthermore, our decomposition facilitates the generation of Monte Carlo toy spectra for sensitivity studies and provides a framework for investigating systematic uncertainties related to solid-state and detector effects. This work establishes a robust foundation for future calorimetric neutrino mass experiments employing $^{163}$Ho, supporting both data analysis and experimental design. △ Less

Submitted 25 March, 2026; v1 submitted 12 July, 2025; originally announced July 2025.

Journal ref: J. High Energ. Phys. 2026, 215 (2026)

An array of bulk-acoustic-wave sensors as a high-frequency antenna for gravitational waves

Authors: G. Albani, M. Borghesi, L. Canonica, R. Carobene, F. De Guio, M. Faverzani, E. Ferri, R. Gerosa, A. Ghezzi, A. Giachero, C. Gotti, D. Labranca, L. Mariani, A. Nucciotti, G. Pessina, D. Rozza, T. Tabarelli de Fatis

Abstract: In their simplest form, bulk acoustic wave (BAW) devices consist of a piezoelectric crystal between two electrodes that transduce the material's vibrations into electrical signals. They are adopted in frequency control and metrology, with well-established standards at frequencies of 5~MHz and above. Their use as a resonant-mass strain antenna for high-frequency gravitational waves has been recentl… ▽ More In their simplest form, bulk acoustic wave (BAW) devices consist of a piezoelectric crystal between two electrodes that transduce the material's vibrations into electrical signals. They are adopted in frequency control and metrology, with well-established standards at frequencies of 5~MHz and above. Their use as a resonant-mass strain antenna for high-frequency gravitational waves has been recently proposed (Goryachev and Tobar, 2014). The estimated power spectral density sensitivity at the resonant frequencies is of the order of $10^{-21}\, \textrm{strain}/\sqrt{\textrm{Hz}}$. In this paper, after introducing the science opportunity and potential of gravitational wave detection with BAWs, we describe the two-stage BAUSCIA project plan to build a multimode antenna based on commercial BAWs, followed by an optimized array of custom BAWs. We show that commercially available BAWs already provide sensitivity comparable to current experiments around 10~MHz. Finally, we outline options for optimization of custom devices to improve sensitivity in an unexplored region, probe multiple frequencies between 0.1 and 10 MHz, and target specific signals, such as post-merger emission from neutron stars or emission from various dark matter candidates. △ Less

Submitted 20 June, 2025; originally announced June 2025.

Journal ref: Galaxies 2025, 13(4), 94

Impact of embedded $^{163}$Ho on the performance of the transition-edge sensor microcalorimeters of the HOLMES experiment

Authors: Douglas Bennett, Matteo Borghesi, Pietro Campana, Rodolfo Carobene, Giancarlo Ceruti, Matteo De Gerone, Marco Faverzani, Lorenzo Ferrari Barusso, Elena Ferri, Joseph Fowler, Sara Gamba, Flavio Gatti, Andrea Giachero, Marco Gobbo, Danilo Labranca, Roberto Moretti, Angelo Nucciotti, Luca Origo, Stefano Ragazzi, Dan Schmidt, Daniel Swetz, Joel Ullom

Abstract: We present a detailed investigation of the performance of transition-edge sensor (TES) microcalorimeters with $^{163}$Ho atoms embedded by ion implantation, as part of the HOLMES experiment aimed at neutrino mass determination. The inclusion of $^{163}$Ho atoms introduces an excess heat capacity due to a pronounced Schottky anomaly, which can affect the detector's energy resolution, signal height,… ▽ More We present a detailed investigation of the performance of transition-edge sensor (TES) microcalorimeters with $^{163}$Ho atoms embedded by ion implantation, as part of the HOLMES experiment aimed at neutrino mass determination. The inclusion of $^{163}$Ho atoms introduces an excess heat capacity due to a pronounced Schottky anomaly, which can affect the detector's energy resolution, signal height, and response time. We fabricated TES arrays with varying levels of $^{163}$Ho activity and characterized their performance in terms of energy resolution, decay time constants, and heat capacity. The intrinsic energy resolution was found to degrade with increasing $^{163}$Ho activity, consistent with the expected scaling of heat capacity. From the analysis, we determined the specific heat capacity of $^{163}$Ho to be $(2.9 \pm 0.4 \mathrm{(stat)} \pm 0.7 \mathrm{(sys)})$ J/K/mol at $(94 \pm 1)$\,mK, close to the literature values for metallic holmium. No additional long decay time constants correlated with $^{163}$Ho activity were observed, indicating that the excess heat capacity does not introduce weakly coupled thermodynamic systems. These results suggest that our present TES microcalorimeters can tolerate $^{163}$Ho activities up to approximately 5 Bq without significant performance degradation. For higher activities, reducing the TES transition temperature is necessary to maintain energy resolution. These findings provide critical insights for optimizing TES microcalorimeters for future neutrino mass experiments and other applications requiring embedded radioactive sources. The study also highlights the robustness of TES technology in handling implanted radionuclides while maintaining high-resolution performance. △ Less

Submitted 1 October, 2025; v1 submitted 16 June, 2025; originally announced June 2025.

Comments: Published on The European Physics Journal C

Journal ref: Eur. Phys. J. C 85, 1087 (2025)

Most stringent bound on electron neutrino mass obtained with a scalable low temperature microcalorimeter array

Authors: B. K. Alpert, M. Balata, D. T. Becker, D. A. Bennett, M. Borghesi, P. Campana, R. Carobene, M. De Gerone, W. B. Doriese, M. Faverzani, L. Ferrari Barusso, E. Ferri, J. W. Fowler, G. Gallucci, S. Gamba, J. D. Gard, F. Gatti, A. Giachero, M. Gobbo, U. Köster, D. Labranca, M. Lusignoli, P. Manfrinetti, J. A. B. Mates, E. Maugeri , et al. (14 additional authors not shown)

Abstract: The determination of the absolute neutrino mass scale remains a fundamental open question in particle physics, with profound implications for both the Standard Model and cosmology. Direct kinematic measurements, independent of model-dependent assumptions, provide the most robust approach to address this challenge. In this Letter, we present the most stringent upper bound on the effective electron… ▽ More The determination of the absolute neutrino mass scale remains a fundamental open question in particle physics, with profound implications for both the Standard Model and cosmology. Direct kinematic measurements, independent of model-dependent assumptions, provide the most robust approach to address this challenge. In this Letter, we present the most stringent upper bound on the effective electron neutrino mass ever obtained with a calorimetric measurement of the electron capture decay of $^{163}$Ho. The HOLMES experiment employs an array of ion-implanted transition-edge sensor (TES) microcalorimeters, achieving an average energy resolution of 6 eV FWHM with a scalable, multiplexed readout technique. With a total of $7\times10^7$ decay events recorded over two months and a Bayesian statistical analysis, we derive an upper limit of $m_β<27$ eV/c$^2$ at 90% credibility. These results validate the feasibility of $^{163}$Ho calorimetry for next-generation neutrino mass experiments and demonstrate the potential of a scalable TES-based microcalorimetric technique to push the sensitivity of direct neutrino mass measurements beyond the current state of the art. △ Less

Submitted 29 September, 2025; v1 submitted 10 March, 2025; originally announced March 2025.

Comments: 12 pages, 7 figures. Published on PRL

Journal ref: Phys. Rev. Lett. 135, 141801 (2025)

A Demonstration of Slowed Electron ${\bf E} \times {\bf B}$ Drift for PTOLEMY

Authors: M. Farino, A. Tan, A. Apponi, M. Betti, M. Borghesi, A. Casale, O. Castellano, G. Cavoto, L. Cecchini, E. Celasco, W. Chung, A. G. Cocco, A. Colijn, B. Corcione, N. D'Ambrosio, N. de Groot, S. el Morabit, A. Esposito, M. Faverzani, A. D. Ferella, E. Ferri, L. Ficcadenti, S. Gamba, S. Gariazzo, H. Garrone , et al. (36 additional authors not shown)

Abstract: To resolve the effective neutrino mass $m_β$ with an energy resolution of 50~meV, the PTOLEMY experiment has proposed a novel transverse electromagnetic filtering process. Substantially reducing the kinetic energy of tritium $β$-decay electrons by counteracting motion from ${\bf E}$ $\times$ ${\bf B}$ and $\nabla{\rm B}$ drift, the PTOLEMY filter requires an input of emitted electron kinematic inf… ▽ More To resolve the effective neutrino mass $m_β$ with an energy resolution of 50~meV, the PTOLEMY experiment has proposed a novel transverse electromagnetic filtering process. Substantially reducing the kinetic energy of tritium $β$-decay electrons by counteracting motion from ${\bf E}$ $\times$ ${\bf B}$ and $\nabla{\rm B}$ drift, the PTOLEMY filter requires an input of emitted electron kinematic information to generate a tailored, suitable electric field for each candidate. The collaboration proposes to extract these quantities by using antennae to observe the relativistic frequency shift of emitted cyclotron radiation as an electron transits by ${\bf E}$ $\times$ ${\bf B}$ drift through a uniform magnetic field region preceding the filter. Electrons must be contained within this region long enough such that an adequate integrated radiated power signal is received to accurately estimate these kinematics. This necessitates a controlled, slowed drift speed. This paper presents the experimental design to vary ${\bf E}$ $\times$ ${\bf B}$ drift speed of carbon-14 $β$-decay electrons using a custom electrode field cage situated between the pole faces of an electromagnet. Matching our results with high-fidelity simulation, we deduce a capacity to increase particle time of flight by a factor of 5 in the field cage's slow drift region. Limited only by the dimensions of our system, we assert drift speed can be arbitrarily slowed to meet the needs of PTOLEMY's future detector. Actualizing such a system is a crucial milestone in developing the detector, enabling future cyclotron radiation measurements, filter implementation, and source injection. △ Less

Submitted 10 July, 2025; v1 submitted 13 March, 2025; originally announced March 2025.

Comments: 31 pages, 32 figures

Simulation of the Background from $^{13}$C$(α, n)^{16}$O Reaction in the JUNO Scintillator

Authors: JUNO Collaboration, Thomas Adam, Kai Adamowicz, Shakeel Ahmad, Rizwan Ahmed, Sebastiano Aiello, Fengpeng An, Costas Andreopoulos, Giuseppe Andronico, Nikolay Anfimov, Vito Antonelli, Tatiana Antoshkina, João Pedro Athayde Marcondes de André, Didier Auguste, Weidong Bai, Nikita Balashov, Andrea Barresi, Davide Basilico, Eric Baussan, Marco Beretta, Antonio Bergnoli, Nikita Bessonov, Daniel Bick, Lukas Bieger, Svetlana Biktemerova , et al. (608 additional authors not shown)

Abstract: Large-scale organic liquid scintillator detectors are highly efficient in the detection of MeV-scale electron antineutrinos. These signal events can be detected through inverse beta decay on protons, which produce a positron accompanied by a neutron. A noteworthy background for antineutrinos coming from nuclear power reactors and from the depths of the Earth (geoneutrinos) is generated by ($α, n$)… ▽ More Large-scale organic liquid scintillator detectors are highly efficient in the detection of MeV-scale electron antineutrinos. These signal events can be detected through inverse beta decay on protons, which produce a positron accompanied by a neutron. A noteworthy background for antineutrinos coming from nuclear power reactors and from the depths of the Earth (geoneutrinos) is generated by ($α, n$) reactions. In organic liquid scintillator detectors, $α$ particles emitted from intrinsic contaminants such as $^{238}$U, $^{232}$Th, and $^{210}$Pb/$^{210}$Po, can be captured on $^{13}$C nuclei, followed by the emission of a MeV-scale neutron. Three distinct interaction mechanisms can produce prompt energy depositions preceding the delayed neutron capture, leading to a pair of events correlated in space and time within the detector. Thus, ($α, n$) reactions represent an indistinguishable background in liquid scintillator-based antineutrino detectors, where their expected rate and energy spectrum are typically evaluated via Monte Carlo simulations. This work presents results from the open-source SaG4n software, used to calculate the expected energy depositions from the neutron and any associated de-excitation products. Also simulated is a detailed detector response to these interactions, using a dedicated Geant4-based simulation software from the JUNO experiment. An expected measurable $^{13}$C$(α, n)^{16}$O event rate and reconstructed prompt energy spectrum with associated uncertainties, are presented in the context of JUNO, however, the methods and results are applicable and relevant to other organic liquid scintillator neutrino detectors. △ Less

Submitted 2 May, 2025; v1 submitted 2 March, 2025; originally announced March 2025.

Comments: 25 pages, 14 figures, 4 tables

Fluorescence emission of the JUNO liquid scintillator

Authors: M. Beretta, F. Houria, F. Ferraro, D. Basilico, A. Brigatti, B. Caccianiga, A. Caslini, C. Landini, P. Lombardi, L. Pelicci, E. Percalli, G. Ranucci, A. C. Re, C. Clementi, F. Ortica, A. Romani, V. Antonelli, M. G. Giammarchi, L. Miramonti, P. Saggese, M. D. C. Torri, S. Aiello, G. Andronico, A. Barresi, A. Bergnoli , et al. (43 additional authors not shown)

Abstract: JUNO is a huge neutrino detector that will use 20 kton of organic liquid scintillator as its detection medium. The scintillator is a mixture of linear alkyl benzene (LAB), 2.5 g/L of 2,5-diphenyloxazole (PPO) and 3 mg/L of 1,4-Bis(2-methylstyryl)benzene (Bis-MSB). The main goal of JUNO is to determine the Neutrino Mass Ordering [1, 2, 3]. In order to achieve this purpose, good energy and position… ▽ More JUNO is a huge neutrino detector that will use 20 kton of organic liquid scintillator as its detection medium. The scintillator is a mixture of linear alkyl benzene (LAB), 2.5 g/L of 2,5-diphenyloxazole (PPO) and 3 mg/L of 1,4-Bis(2-methylstyryl)benzene (Bis-MSB). The main goal of JUNO is to determine the Neutrino Mass Ordering [1, 2, 3]. In order to achieve this purpose, good energy and position reconstruction is required, hence a complete understanding of the optical characteristics of the liquid scintillator is mandatory. In this paper we present the measurements on the JUNO scintillator emission spectrum, absorption length and fluorescence time distribution performed respectively with a spectrofluorimeter, a spectrophotometer and a custom made setup △ Less

Submitted 9 March, 2025; v1 submitted 17 January, 2025; originally announced January 2025.

Journal ref: Journal of Instrumentation, Volume 20, May 2025

Interpretable machine learning approach for electron antineutrino selection in a large liquid scintillator detector

Authors: A. Gavrikov, V. Cerrone, A. Serafini, R. Brugnera, A. Garfagnini, M. Grassi, B. Jelmini, L. Lastrucci, S. Aiello, G. Andronico, V. Antonelli, A. Barresi, D. Basilico, M. Beretta, A. Bergnoli, M. Borghesi, A. Brigatti, R. Bruno, A. Budano, B. Caccianiga, A. Cammi, R. Caruso, D. Chiesa, C. Clementi, S. Dusini , et al. (43 additional authors not shown)

Abstract: Several neutrino detectors, KamLAND, Daya Bay, Double Chooz, RENO, and the forthcoming large-scale JUNO, rely on liquid scintillator to detect reactor antineutrino interactions. In this context, inverse beta decay represents the golden channel for antineutrino detection, providing a pair of correlated events, thus a strong experimental signature to distinguish the signal from a variety of backgrou… ▽ More Several neutrino detectors, KamLAND, Daya Bay, Double Chooz, RENO, and the forthcoming large-scale JUNO, rely on liquid scintillator to detect reactor antineutrino interactions. In this context, inverse beta decay represents the golden channel for antineutrino detection, providing a pair of correlated events, thus a strong experimental signature to distinguish the signal from a variety of backgrounds. However, given the low cross-section of antineutrino interactions, the development of a powerful event selection algorithm becomes imperative to achieve effective discrimination between signal and backgrounds. In this study, we introduce a machine learning (ML) model to achieve this goal: a fully connected neural network as a powerful signal-background discriminator for a large liquid scintillator detector. We demonstrate, using the JUNO detector as an example, that, despite the already high efficiency of a cut-based approach, the presented ML model can further improve the overall event selection efficiency. Moreover, it allows for the retention of signal events at the detector edges that would otherwise be rejected because of the overwhelming amount of background events in that region. We also present the first interpretable analysis of the ML approach for event selection in reactor neutrino experiments. This method provides insights into the decision-making process of the model and offers valuable information for improving and updating traditional event selection approaches. △ Less

Submitted 25 November, 2024; v1 submitted 9 June, 2024; originally announced June 2024.

Comments: This is a post-peer-review, pre-copyedit version of an article published in Phys. Lett. B. The final published version is available online: https://www.sciencedirect.com/science/article/pii/S0370269324006993

Journal ref: Physics Letters B 860, 139141 (2025)

Distillation and Stripping purification plants for JUNO liquid scintillator

Authors: C. Landini, M. Beretta, P. Lombardi, A. Brigatti, M. Montuschi, S. Parmeggiano, G. Ranucci, V. Antonelli, D. Basilico, B. Caccianiga, M. G. Giammarchi, L. Miramonti, E. Percalli, A. C. Re, P. Saggese, M. D. C. Torri, S. Aiello, G. Andronico, A. Barresi, A. Bergnoli, M. Borghesi, R. Brugnera, R. Bruno, A. Budano, A. Cammi , et al. (42 additional authors not shown)

Abstract: The optical and radiochemical purification of the scintillating liquid, which will fill the central detector of the JUNO experiment, plays a crucial role in achieving its scientific goals. Given its gigantic mass and dimensions and an unprecedented target value of about 3% @ 1 MeV in energy resolution, JUNO has set severe requirements on the parameters of its scintillator, such as attenuation leng… ▽ More The optical and radiochemical purification of the scintillating liquid, which will fill the central detector of the JUNO experiment, plays a crucial role in achieving its scientific goals. Given its gigantic mass and dimensions and an unprecedented target value of about 3% @ 1 MeV in energy resolution, JUNO has set severe requirements on the parameters of its scintillator, such as attenuation length (Lat>20 m at 430 nm), transparency, light yield, and content of radioactive contaminants (238U,232Th<10-15 g/g). To accomplish these needs, the scintillator will be processed using several purification methods, including distillation in partial vacuum and gas stripping, which are performed in two large scale plants installed at the JUNO site. In this paper, layout, operating principles, and technical aspects which have driven the design and construction of the distil- lation and gas stripping plants are reviewed. The distillation is effective in enhancing the optical properties and removing heavy radio-impurities (238U,232Th, 40K), while the stripping process exploits pure water steam and high-purity nitrogen to extract gaseous contaminants (222Rn, 39Ar, 85Kr, O2) from the scintillator. The plant operating parameters have been tuned during the recent com- missioning phase at the JUNO site and several QA/QC measurements and tests have been performed to evaluate the performances of the plants. Some preliminary results on the efficiency of these purification processes will be shown. △ Less

Submitted 3 June, 2024; originally announced June 2024.

Comments: 11 pages, 7 figures

Refractive index in the JUNO liquid scintillator

Authors: H. S. Zhang, M. Beretta, S. Cialdi, C. X. Yang, J. H. Huang, F. Ferraro, G. F. Cao, G. Reina, Z. Y. Deng, E. Suerra, S. Altilia, V. Antonelli, D. Basilico, A. Brigatti, B. Caccianiga, M. G. Giammarchi, C. Landini, P. Lombardi, L. Miramonti, E. Percalli, G. Ranucci, A. C. Re, P. Saggese, M. D. C. Torri, S. Aiello , et al. (51 additional authors not shown)

Abstract: In the field of rare event physics, it is common to have huge masses of organic liquid scintillator as detection medium. In particular, they are widely used to study neutrino properties or astrophysical neutrinos. Thanks to its safety properties (such as low toxicity and high flash point) and easy scalability, linear alkyl benzene is the most common solvent used to produce liquid scintillators for… ▽ More In the field of rare event physics, it is common to have huge masses of organic liquid scintillator as detection medium. In particular, they are widely used to study neutrino properties or astrophysical neutrinos. Thanks to its safety properties (such as low toxicity and high flash point) and easy scalability, linear alkyl benzene is the most common solvent used to produce liquid scintillators for large mass experiments. The knowledge of the refractive index is a pivotal point to understand the detector response, as this quantity (and its wavelength dependence) affects the Cherenkov radiation and photon propagation in the medium. In this paper, we report the measurement of the refractive index of the JUNO liquid scintillator between 260-1064 nm performed with two different methods (an ellipsometer and a refractometer), with a sub percent level precision. In addition, we used an interferometer to measure the group velocity in the JUNO liquid scintillator and verify the expected value derived from the refractive index measurements. △ Less

Submitted 30 May, 2024; originally announced May 2024.

Comments: 6 pages, 9 figures

Saturation of the compression of two interacting magnetic flux tubes evidenced in the laboratory

Authors: A. Sladkov, C. Fegan, W. Yao, A. F. A. Bott, S. N. Chen, H. Ahmed, E. D. Filippov, R. Lelièvre, P. Martin, A. McIlvenny, T. Waltenspiel, P. Antici, M. Borghesi, S. Pikuz, A. Ciardi, E. d'Humières, A. Soloviev, M. Starodubtsev, J. Fuchs

Abstract: Interactions between magnetic fields advected by matter play a fundamental role in the Universe at a diverse range of scales. A crucial role these interactions play is in making turbulent fields highly anisotropic, leading to observed ordered fields. These in turn, are important evolutionary factors for all the systems within and around. Despite scant evidence, due to the difficulty in measuring e… ▽ More Interactions between magnetic fields advected by matter play a fundamental role in the Universe at a diverse range of scales. A crucial role these interactions play is in making turbulent fields highly anisotropic, leading to observed ordered fields. These in turn, are important evolutionary factors for all the systems within and around. Despite scant evidence, due to the difficulty in measuring even near-Earth events, the magnetic field compression factor in these interactions, measured at very varied scales, is limited to a few. However, compressing matter in which a magnetic field is embedded, results in compression up to several thousands. Here we show, using laboratory experiments and matching three-dimensional hybrid simulations, that there is indeed a very effective saturation of the compression when two independent parallel-oriented magnetic fields regions encounter one another due to plasma advection. We found that the observed saturation is linked to a build-up of the magnetic pressure, which decelerates and redirects the inflows at their encounter point, thereby stopping further compression. Moreover, the growth of an electric field, induced by the incoming flows and the magnetic field, acts in redirecting the inflows transversely, further hampering field compression. △ Less

Submitted 29 November, 2024; v1 submitted 18 April, 2024; originally announced April 2024.

Development of KI-TWPAs for the DARTWARS project

Authors: Felix Ahrens, Elena Ferri, Guerino Avallone, Carlo Barone, Matteo Borghesi, Luca Callegaro, Giovanni Carapella, Anna Paola Caricato, Iacopo Carusotto, Alessandro Cian, Alessandro D'Elia, Daniele Di Gioacchino, Emanuele Enrico, Paolo Falferi, Luca Fasolo, Marco Faverzani, Giovanni Filatrella, Claudio Gatti, Andrea Giachero, Damiano Giubertoni, Veronica Granata, Claudio Guarcello, Danilo Labranca, Angelo Leo, Carlo Ligi , et al. (18 additional authors not shown)

Abstract: Noise at the quantum limit over a broad bandwidth is a fundamental requirement for future cryogenic experiments for neutrino mass measurements, dark matter searches and Cosmic Microwave Background (CMB) measurements as well as for fast high-fidelity read-out of superconducting qubits. In the last years, Josephson Parametric Amplifiers (JPA) have demonstrated noise levels close to the quantum limit… ▽ More Noise at the quantum limit over a broad bandwidth is a fundamental requirement for future cryogenic experiments for neutrino mass measurements, dark matter searches and Cosmic Microwave Background (CMB) measurements as well as for fast high-fidelity read-out of superconducting qubits. In the last years, Josephson Parametric Amplifiers (JPA) have demonstrated noise levels close to the quantum limit, but due to their narrow bandwidth, only few detectors or qubits per line can be read out in parallel. An alternative and innovative solution is based on superconducting parametric amplification exploiting the travelling-wave concept. Within the DARTWARS (Detector Array Readout with Travelling Wave AmplifieRS) project, we develop Kinetic Inductance Travelling-Wave Parametric Amplifiers (KI-TWPAs) for low temperature detectors and qubit read-out. KI-TWPAs are typically operated in a threewave mixing (3WM) mode and are characterised by a high gain, a high saturation power, a large amplification bandwidth and nearly quantum limited noise performance. The goal of the DARTWARS project is to optimise the KI-TWPA design, explore new materials, and investigate alternative fabrication processes in order to enhance the overall performance of the amplifier. In this contribution we present the advancements made by the DARTWARS collaboration to produce a working prototype of a KI-TWPA, from the fabrication to the characterisation. △ Less

Submitted 19 February, 2024; originally announced February 2024.

Journal ref: IEEE Transactions on Applied Superconductivity, vol. 34, no. 3, pp. 1-5, May 2024, Art no. 1700605

Weibel- and non-resonant Whistler wave growth in an expanding plasma in a 1D simulation geometry

Authors: M E Dieckmann, L Palodhi, C Fegan, M Borghesi

Abstract: Ablating a target with an ultraintense laser pulse can create a cloud of collisionless plasma. A density ramp forms, in which the plasma density decreases and the ion's mean speed increases with distance from the plasma source. Its width increases with time. Electrons lose energy in the ion's expansion direction, which gives them a temperature anisotropy. We study with one-dimensional particle-in-… ▽ More Ablating a target with an ultraintense laser pulse can create a cloud of collisionless plasma. A density ramp forms, in which the plasma density decreases and the ion's mean speed increases with distance from the plasma source. Its width increases with time. Electrons lose energy in the ion's expansion direction, which gives them a temperature anisotropy. We study with one-dimensional particle-in-cell simulations the expansion of a dense plasma into a dilute one, yielding a density ramp similar to that in laser plasma experiments and a thermal-anisotropy-driven instability. Non-propagating Weibel-type modes grow in the simulation with no initial magnetic field. Their magnetic field diffuses across the the shock and expands upstream. Circularly polarized propagating Whistler waves grow in a second simulation, in which a magnetic field is aligned with the ion expansion direction. Both wave modes are driven by non-resonant instabilities, they have a similar exponential growth rates, and they can leave the density ramp and expand into the dilute plasma. Their large magnetic amplitude should make them detectable in experimental settings. △ Less

Submitted 6 February, 2024; originally announced February 2024.

Comments: 18 pages, 9 figures, accepted for publication in Physica Scripta

Global Characterization of a Laser-Generated Neutron Source

Authors: D. P. Higginson, R. Lelièvre, L. Vassura, M. M. Gugiu, M. Borghesi, L. A. Bernstein, D. L. Bleuel, B. L. Goldblum, A. Green, F. Hannachi, S. Kar, S. Kisyov, L. Quentin, M. Schroer, M. Tarisien, O. Willi, P. Antici, F. Negoita, A. Allaoua, J. Fuchs

Abstract: Laser-driven neutron sources are routinely produced by the interaction of laser-accelerated protons with a converter. They present complementary characteristics to those of conventional accelerator-based neutron sources (e.g. short pulse durations, enabling novel applications like radiography). We present here results from an experiment aimed at performing a global characterization of the neutrons… ▽ More Laser-driven neutron sources are routinely produced by the interaction of laser-accelerated protons with a converter. They present complementary characteristics to those of conventional accelerator-based neutron sources (e.g. short pulse durations, enabling novel applications like radiography). We present here results from an experiment aimed at performing a global characterization of the neutrons produced using the Titan laser at the Jupiter Laser Facility (Livermore, USA), where protons were accelerated from 23 $μm$ thick plastic targets and directed onto a LiF converter to produce neutrons. For this purpose, several diagnostics were used to measure these neutron emissions, such as CR-39, activation foils, Time-of-Flight detectors and direct measurement of $^{7}$Be residual activity in the LiF converters. The use of these different, independently operating diagnostics enables comparison of the various measurements performed to provide a robust characterization. These measurements led to a neutron yield of $2.10^{9}$ neutrons per shot with a modest angular dependence, close to that simulated. △ Less

Submitted 21 December, 2023; originally announced December 2023.

Analysis of reactor burnup simulation uncertainties for antineutrino spectrum prediction

Authors: A. Barresi, M. Borghesi, A. Cammi, D. Chiesa, L. Loi, M. Nastasi, E. Previtali, M. Sisti, S. Aiello, G. Andronico, V. Antonelli, D. Basilico, M. Beretta, A. Bergnoli, A. Brigatti, R. Brugnera, R. Bruno, A. Budano, B. Caccianiga, V. Cerrone, R. Caruso, C. Clementi, S. Dusini, A. Fabbri, G. Felici , et al. (42 additional authors not shown)

Abstract: Nuclear reactors are a source of electron antineutrinos due to the presence of unstable fission products that undergo $β^-$ decay. They will be exploited by the JUNO experiment to determine the neutrino mass ordering and to get very precise measurements of the neutrino oscillation parameters. This requires the reactor antineutrino spectrum to be characterized as precisely as possible both through… ▽ More Nuclear reactors are a source of electron antineutrinos due to the presence of unstable fission products that undergo $β^-$ decay. They will be exploited by the JUNO experiment to determine the neutrino mass ordering and to get very precise measurements of the neutrino oscillation parameters. This requires the reactor antineutrino spectrum to be characterized as precisely as possible both through high resolution measurements, as foreseen by the TAO experiment, and detailed simulation models. In this paper we present a benchmark analysis utilizing Serpent Monte Carlo simulations in comparison with real pressurized water reactor spent fuel data. Our objective is to study the accuracy of fission fraction predictions as a function of different reactor simulation approximations. Then, utilizing the BetaShape software, we construct fissile antineutrino spectra using the summation method, thereby assessing the influence of simulation uncertainties on reactor antineutrino spectrum. △ Less

Submitted 30 October, 2024; v1 submitted 21 November, 2023; originally announced November 2023.

Journal ref: Eur. Phys. J. Plus 139, 952 (2024)

High kinetic inductance NbTiN films for quantum limited travelling wave parametric amplifiers

Authors: Federica Mantegazzini, Felix Ahrens, Matteo Borghesi, Paolo Falferi, Luca Fasolo, Marco Faverzani, Elena Ferri, Danilo Labranca, Benno Margesin, Renato Mezzena, Roberto Moretti, Angelo Nucciotti, Luca Origo, Andrea Vinante, Mario Zannoni, Andrea Giachero

Abstract: A wide-bandwidth and low-noise amplification chain in the microwave regime is crucial for the efficient read-out of quantum systems based on superconducting detectors, such as Microwave Kinetic Inductance Detectors (MKIDs), Transition Edge Sensors (TESs), Magnetic Microcalorimeters (MMCs), and RF cavities, as well as qubits. Kinetic Inductance Travelling Wave Parametric Amplifiers (KI-TWPAs) opera… ▽ More A wide-bandwidth and low-noise amplification chain in the microwave regime is crucial for the efficient read-out of quantum systems based on superconducting detectors, such as Microwave Kinetic Inductance Detectors (MKIDs), Transition Edge Sensors (TESs), Magnetic Microcalorimeters (MMCs), and RF cavities, as well as qubits. Kinetic Inductance Travelling Wave Parametric Amplifiers (KI-TWPAs) operated in a three-wave mixing fashion have demonstrated exceptional dynamic range and low-noise performance, approaching the quantum limit. These amplifiers can be fabricated using a single layer of a high kinetic inductance film as weakly dispersive artificial transmission lines, with the ability to control the phase-matched bandwidth through dispersion engineering. In this study, we present the optimisation of the rf sputter-deposition process of NbTiN films using a Nb80%T20 target, with the goal of achieving precise control over film characteristics, resulting in high kinetic inductance while maintaining a high transition temperature. The parameter landscape related to the different sputtering conditions, such as pressure, power, and nitrogen flow, has been explored and the film thickness has been used as a fine-tuning parameter to adjust the properties of the final NbTiN films used for the fabrication of KI-TWPAs. As a final result, we have obtained a NbTiN film with a kinetic inductance of 8.5 pH/sq which we have exploited to fabricate KI-TWPA prototype devices, showing promising amplification performance. △ Less

Submitted 18 October, 2023; v1 submitted 17 October, 2023; originally announced October 2023.

Automated control and optimisation of laser driven ion acceleration

Authors: B. Loughran, M. J. V. Streeter, H. Ahmed, S. Astbury, M. Balcazar, M. Borghesi, N. Bourgeois, C. B. Curry, S. J. D. Dann, S. DiIorio, N. P. Dover, T. Dzelzanis, O. C. Ettlinger, M. Gauthier, L. Giuffrida, G. D. Glenn, S. H. Glenzer, J. S. Green, R. J. Gray, G. S. Hicks, C. Hyland, V. Istokskaia, M. King, D. Margarone, O. McCusker , et al. (10 additional authors not shown)

Abstract: The interaction of relativistically intense lasers with opaque targets represents a highly non-linear, multi-dimensional parameter space. This limits the utility of sequential 1D scanning of experimental parameters for the optimisation of secondary radiation, although to-date this has been the accepted methodology due to low data acquisition rates. High repetition-rate (HRR) lasers augmented by ma… ▽ More The interaction of relativistically intense lasers with opaque targets represents a highly non-linear, multi-dimensional parameter space. This limits the utility of sequential 1D scanning of experimental parameters for the optimisation of secondary radiation, although to-date this has been the accepted methodology due to low data acquisition rates. High repetition-rate (HRR) lasers augmented by machine learning present a valuable opportunity for efficient source optimisation. Here, an automated, HRR-compatible system produced high fidelity parameter scans, revealing the influence of laser intensity on target pre-heating and proton generation. A closed-loop Bayesian optimisation of maximum proton energy, through control of the laser wavefront and target position, produced proton beams with equivalent maximum energy to manually-optimized laser pulses but using only 60% of the laser energy. This demonstration of automated optimisation of laser-driven proton beams is a crucial step towards deeper physical insight and the construction of future radiation sources. △ Less

Submitted 1 March, 2023; originally announced March 2023.

Comments: 11 pages

Assessment of the reliability of Deconvolution Procedures for RCF Spectroscopy of Laser-Driven Ion Beams

Authors: S. McCallum, G. Milluzzo, M. Borghesi, A. Subiel, F. Romano

Abstract: Laser-driven ion beams are defined by a number of unique features, including a large spread in energy. A stack configuration of radiochromic film (RCF) can be utilized to characterize such beams through measurements of their energy spectra. A spectroscopic procedure is reported that allows the proton energy density within each active layer of a radiochromic film (RCF) stack to be retrieved. This i… ▽ More Laser-driven ion beams are defined by a number of unique features, including a large spread in energy. A stack configuration of radiochromic film (RCF) can be utilized to characterize such beams through measurements of their energy spectra. A spectroscopic procedure is reported that allows the proton energy density within each active layer of a radiochromic film (RCF) stack to be retrieved. This is based upon on a deconvolution algorithm developed through Geant4 Monte Carlo simulations to correct the contributions of energy depositions within a given film layer. Through Monte Carlo calculations, the spectrum retrieved from a simulated film stack can be retrieved and compared with a known energy spectrum, providing an examination of the efficacy of this tool. Application of the developed deconvolution procedure thus offers the potential to correctly reconstruct the incident energy spectrum of a laser-driven proton and ion beam from a stack of irradiated RCF. △ Less

Submitted 20 January, 2023; originally announced January 2023.

Comments: 6 pages, 3 figures, submission as a proceeding to ECPD 2021

Journal ref: Journal of Instrumentation, Volume 17, February 2022

Proton Imaging of High-Energy-Density Laboratory Plasmas

Authors: Derek B. Schaeffer, Archie F. A. Bott, Marco Borghesi, Kirk A. Flippo, William Fox, Julien Fuchs, Chikang Li, Hye-Sook Park, Fredrick H. Seguin, Petros Tzeferacos, Louise Willingale

Abstract: Proton imaging has become a key diagnostic for measuring electromagnetic fields in high-energy-density (HED) laboratory plasmas. Compared to other techniques for diagnosing fields, proton imaging is a non-perturbative measurement that can simultaneously offer high spatial and temporal resolution and the ability to distinguish between electric and magnetic fields. Consequently, proton imaging has b… ▽ More Proton imaging has become a key diagnostic for measuring electromagnetic fields in high-energy-density (HED) laboratory plasmas. Compared to other techniques for diagnosing fields, proton imaging is a non-perturbative measurement that can simultaneously offer high spatial and temporal resolution and the ability to distinguish between electric and magnetic fields. Consequently, proton imaging has been used in a wide range of HED experiments, from inertial confinement fusion to laboratory astrophysics. An overview is provided on the state of the art of proton imaging, including detailed discussion of experimental considerations like proton sources and detectors, the theory of proton-imaging analysis, and a survey of experimental results demonstrating the breadth of applications. Topics at the frontiers of proton imaging development are also described, along with an outlook on the future of the field. △ Less

Submitted 15 December, 2022; originally announced December 2022.

Dynamics of nanosecond laser pulse propagation and of associated instabilities in a magnetized underdense plasma

Authors: W. Yao, A. Higginson, J. -R. Marquès, P. Antici, J. Béard, K. Burdonov, M. Borghesi, A. Castan, A. Ciardi, B. Coleman, S. N. Chen, E. d'Humières, T. Gangolf, L. Gremillet, B. Khiar, L. Lancia, P. Loiseau, X. Ribeyre, A. Soloviev, M. Starodubtsev, Q. Wang, J. Fuchs

Abstract: The propagation and energy coupling of intense laser beams in plasmas are critical issues in laser-driven inertial confinement fusion. Applying magnetic fields to such a setup has been evoked to enhance fuel confinement and heating, and mitigate laser energy losses. Here we report on experimental measurements demonstrating improved transmission and increased smoothing of a high-power laser beam pr… ▽ More The propagation and energy coupling of intense laser beams in plasmas are critical issues in laser-driven inertial confinement fusion. Applying magnetic fields to such a setup has been evoked to enhance fuel confinement and heating, and mitigate laser energy losses. Here we report on experimental measurements demonstrating improved transmission and increased smoothing of a high-power laser beam propagating in an underdense magnetized plasma. We also measure enhanced backscattering, which our simulations show is due to hot electrons confinement, thus leading to reduced target preheating. △ Less

Submitted 11 November, 2022; originally announced November 2022.

Investigating particle acceleration dynamics in interpenetrating magnetized collisionless super-critical shocks

Authors: W. Yao, A. Fazzini, S. N. Chen, K. Burdonov, J. Béard, M. Borghesi, A. Ciardi, M. Miceli, S. Orlando, X. Ribeyre, E. d'Humières, J. Fuchs

Abstract: Colliding collisionless shocks appear in a great variety of astrophysical phenomena and are thought to be possible sources of particle acceleration in the Universe. We have previously investigated particle acceleration induced by single super-critical shocks (whose magnetosonic Mach number is higher than the critical value of 2.7) (Yao et al. 2021, 2022), as well as the collision of two sub-critic… ▽ More Colliding collisionless shocks appear in a great variety of astrophysical phenomena and are thought to be possible sources of particle acceleration in the Universe. We have previously investigated particle acceleration induced by single super-critical shocks (whose magnetosonic Mach number is higher than the critical value of 2.7) (Yao et al. 2021, 2022), as well as the collision of two sub-critical shocks (Fazzini et al. 2022). Here, we propose to make measurements of accelerated particles from interpenetrating super-critical shocks to observe the ''phase-locking effect'' (Fazzini et al. 2022) from such an event. This effect is predicted to significantly boost the energy spectrum of the energized ions compared to a single supercritical collisionless shock. We thus anticipate that the results obtained in the proposed experiment could have a significant impact on our understanding of one type of primary source (acceleration of thermal ions as opposed to secondary acceleration mechanisms of already energetic ions) of ion energization of particles in the Universe. △ Less

Submitted 12 August, 2022; originally announced August 2022.

Optimizing laser coupling, matter heating, and particle acceleration from solids using multiplexed ultraintense lasers

Authors: Weipeng Yao, Motoaki Nakatsutsumi, Sébastien Buffechoux, Patrizio Antici, Macro Borghesi, Andrea Ciardi, Sophia N. Chen, Emmanuel d'Humières, Laurent Gremillet, Robert Heathcote, Vojtěch Horný, Paul McKenna, Mark N. Quinn, Lorenzo Romagnani, Ryan Royle, Gianluca Sarri, Yasuhiko Sentoku, Hans-Peter Schlenvoigt, Toma Toncian, Olivier Tresca, Laura Vassura, Oswald Willi, Julien Fuchs

Abstract: Realizing the full potential of ultrahigh-intensity lasers for particle and radiation generation will require multi-beam arrangements due to technology limitations. Here, we investigate how to optimize their coupling with solid targets. Experimentally, we show that overlapping two intense lasers in a mirror-like configuration onto a solid with a large preplasma can greatly improve the generation o… ▽ More Realizing the full potential of ultrahigh-intensity lasers for particle and radiation generation will require multi-beam arrangements due to technology limitations. Here, we investigate how to optimize their coupling with solid targets. Experimentally, we show that overlapping two intense lasers in a mirror-like configuration onto a solid with a large preplasma can greatly improve the generation of hot electrons at the target front and ion acceleration at the target backside. The underlying mechanisms are analyzed through multidimensional particle-in-cell simulations, revealing that the self-induced magnetic fields driven by the two laser beams at the target front are susceptible to reconnection, which is one possible mechanism to boost electron energization. In addition, the resistive magnetic field generated during the transport of the hot electrons in the target bulk tends to improve their collimation. Our simulations also indicate that such effects can be further enhanced by overlapping more than two laser beams. △ Less

Submitted 23 February, 2024; v1 submitted 12 August, 2022; originally announced August 2022.

Surface Plasmon-Driven Electron and Proton Acceleration without Grating Coupling

Authors: J. Sarma, A. McIlvenny, N. Das, M. Borghesi, A. Macchi

Abstract: Surface plasmon (SP) excitation in intense laser interaction with solid target can be exploited for enhancing secondary emissions, in particular efficient acceleration of high charge electron bunches. Previous studies have mostly used grating coupling to allow SP excitation, which requires stringent laser contrast conditions to preserve the structural integrity of the target. Here we show via simu… ▽ More Surface plasmon (SP) excitation in intense laser interaction with solid target can be exploited for enhancing secondary emissions, in particular efficient acceleration of high charge electron bunches. Previous studies have mostly used grating coupling to allow SP excitation, which requires stringent laser contrast conditions to preserve the structural integrity of the target. Here we show via simulations that efficient SP electron acceleration for currently available short pulse lasers can occur in a flat foil irradiated at parallel or grazing incidence ($\sim 5^\circ$ with the target surface) without a surface modulation. In turn, the accelerated electrons can be effective for generating proton beams with narrow spectra peaked at $>$100 MeV energies for currently available laser drivers. △ Less

Submitted 6 July, 2022; originally announced July 2022.

Calibration of BAS-TR image plate response to GeV gold ions

Authors: D. Doria, P. Martin, H. Ahmed, A. Alejo, M. Cerchez, S. Ferguson, J. Fernandez-Tobias, J. S. Green, D. Gwynne, F. Hanton, J. Jarrett, D. A. Maclellan, A. McIlvenny, P. McKenna, J. A. Ruiz, M. Swantusch, O. Willi, S. Zhai, M. Borghesi, S. Kar

Abstract: The response of the BAS-TR image plate (IP) was absolutely calibrated using CR-39 track detector for high linear energy transfer (LET) Au ions up to $\sim$1.6 GeV (8.2 MeV/nucleon), accelerated by high-power lasers. The calibration was carried out by employing a high-resolution Thomson parabola spectrometer, which allowed resolving Au ions with closely spaced ionization states up to 58$^+$. A resp… ▽ More The response of the BAS-TR image plate (IP) was absolutely calibrated using CR-39 track detector for high linear energy transfer (LET) Au ions up to $\sim$1.6 GeV (8.2 MeV/nucleon), accelerated by high-power lasers. The calibration was carried out by employing a high-resolution Thomson parabola spectrometer, which allowed resolving Au ions with closely spaced ionization states up to 58$^+$. A response function was obtained by fitting the photo-stimulated luminescence (PSL) per Au ion for different ion energies, which is broadly in agreement with that expected from ion stopping in the active layer of the IP. This calibration would allow quantifying the ion energy spectra for high energy Au ions, which is important for further investigation of the laser-based acceleration of heavy ion beams. △ Less

Submitted 21 February, 2022; originally announced February 2022.

Comments: 6 pages; 4 figures. Submitted to journal for review

Journal ref: Review of Scientific Instruments 93, 033304 (2022)

The matrix optimum filter for Low Temperature Detectors dead-time reduction

Authors: Matteo Borghesi, Marco Faverzani, Cecilia Ferrari, Elena Ferri, Andrea Giachero, Angelo Nucciotti, Luca Origo

Abstract: Experiments aiming at high sensitivities usually demand for a very high statistics in order to reach more precise measurements. However, for those exploiting Low Temperature Detectors (LTDs), a high source activity may represent a drawback, if the events rate becomes comparable with the detector characteristic temporal response. Indeed, since commonly used optimum filtering approaches can only pro… ▽ More Experiments aiming at high sensitivities usually demand for a very high statistics in order to reach more precise measurements. However, for those exploiting Low Temperature Detectors (LTDs), a high source activity may represent a drawback, if the events rate becomes comparable with the detector characteristic temporal response. Indeed, since commonly used optimum filtering approaches can only process LTDs signals well isolated in time, a non-negligible part of the recorded experimental data-set is discarded and hence constitute the dead-time. In the presented study we demonstrate that, thanks to the matrix optimum filtering approach, the dead-time of an experiment exploiting LTDs can be strongly reduced. △ Less

Submitted 27 July, 2022; v1 submitted 14 January, 2022; originally announced January 2022.

Journal ref: Eur. Phys. J. C (2022) 82:421

Implementation and Optimization of the PTOLEMY Transverse Drift Electromagnetic Filter

Authors: A. Apponi, M. G. Betti, M. Borghesi, A. Boscá, F. Calle, N. Canci, G. Cavoto, C. Chang, W. Chung, A. G. Cocco, A. P. Colijn, N. D'Ambrosio, N. de Groot, M. Faverzani, A. Ferella, E. Ferri, L. Ficcadenti, P. Garcia-Abia, G. Garcia Gomez-Tejedor, S. Gariazzo, F. Gatti, C. Gentile, A. Giachero, Y. Hochberg, Y. Kahn , et al. (31 additional authors not shown)

Abstract: The PTOLEMY transverse drift filter is a new concept to enable precision analysis of the energy spectrum of electrons near the tritium beta-decay endpoint. This paper details the implementation and optimization methods for successful operation of the filter. We present the first demonstrator that produces the required magnetic field properties with an iron return-flux magnet. Two methods for the s… ▽ More The PTOLEMY transverse drift filter is a new concept to enable precision analysis of the energy spectrum of electrons near the tritium beta-decay endpoint. This paper details the implementation and optimization methods for successful operation of the filter. We present the first demonstrator that produces the required magnetic field properties with an iron return-flux magnet. Two methods for the setting of filter electrode voltages are detailed. The challenges of low-energy electron transport in cases of low field are discussed, such as the growth of the cyclotron radius with decreasing magnetic field, which puts a ceiling on filter performance relative to fixed filter dimensions. Additionally, low pitch angle trajectories are dominated by motion parallel to the magnetic field lines and introduce non-adiabatic conditions and curvature drift. To minimize these effects and maximize electron acceptance into the filter, we present a three-potential-well design to simultaneously drain the parallel and transverse kinetic energies throughout the length of the filter. These optimizations are shown, in simulation, to achieve low-energy electron transport from a 1 T iron core (or 3 T superconducting) starting field with initial kinetic energy of 18.6 keV drained to <10 eV (<1 eV) in about 80 cm. This result for low field operation paves the way for the first demonstrator of the PTOLEMY spectrometer for measurement of electrons near the tritium endpoint to be constructed at the Gran Sasso National Laboratary (LNGS) in Italy. △ Less

Submitted 24 January, 2022; v1 submitted 23 August, 2021; originally announced August 2021.

Comments: 29 pages, 25 figures

Processing of non-constant baseline pulses: a matrix technique

Authors: C. Ferrari, M. Borghesi, M. Faverzani, E. Ferri, A. Giachero, A. Nucciotti

Abstract: For a high source activity experiment, such as HOLMES, non-constant baseline pulses could constitute a great fraction of the data-set. We test the optimal filter matrix technique, proposed to process these pulses, on simulated responses of HOLMES microcalorimeters. For a high source activity experiment, such as HOLMES, non-constant baseline pulses could constitute a great fraction of the data-set. We test the optimal filter matrix technique, proposed to process these pulses, on simulated responses of HOLMES microcalorimeters. △ Less

Submitted 26 July, 2021; originally announced July 2021.

Journal ref: IL NUOVO CIMENTO 44 C (2021)

Spectrally peaked proton beams shock accelerated from an optically shaped overdense gas jet by a near-infrared laser

Authors: George S. Hicks, Oliver C. Ettlinger, Marco Borghesi, David C. Carroll, Robert J. Clarke, Emma-Jane Ditter, Timothy P. Frazer, Ross J. Gray, Aodhan McIlvenny, Paul McKenna, Charlotte A. J. Palmer, Louise Willingale, Zulfikar Najmudin

Abstract: We report on the generation of impurity-free proton beams from an overdense gas jet driven by a near-infrared laser ($λ_L=1.053$ $\mathrmμ m$). The gas profile was shaped prior to the interaction using a controlled prepulse. Without this optical shaping, a 30$\pm$4 nCsr$^{-1}$ thermal spectrum was detected transversely to the laser propagation direction with a high energy 8.27$\pm$7 MeV, narrow en… ▽ More We report on the generation of impurity-free proton beams from an overdense gas jet driven by a near-infrared laser ($λ_L=1.053$ $\mathrmμ m$). The gas profile was shaped prior to the interaction using a controlled prepulse. Without this optical shaping, a 30$\pm$4 nCsr$^{-1}$ thermal spectrum was detected transversely to the laser propagation direction with a high energy 8.27$\pm$7 MeV, narrow energy spread (6$\pm$2 %) bunch containing 45$\pm$7 pCsr$^{-1}$. In contrast, with optical shaping the radial component was not detected and instead forward going protons were detected with energy 1.32$\pm$2 MeV, 12.9$\pm$3 % energy spread, and charge 400$\pm$30 pCsr$^{-1}$. Both the forward going and radial narrow energy spread features are indicative of collisionless shock acceleration of the protons. △ Less

Submitted 28 April, 2021; originally announced April 2021.

Comments: 14 pages, 8 figures

Photo-induced pair production and strong field QED on Gemini

Authors: CH Keitel, A Di Piazza, GG Paulus, T Stoehlker, EL Clark, S Mangles, Z Najmudin, K Krushelnick, J Schreiber, M Borghesi, B Dromey, M Geissler, D Riley, G Sarri, M Zepf

Abstract: The extreme intensities obtainable with lasers such as Gemini allow non-linear QED phenomena to be investigated according to our calculations. Electron-positron pair production from a pure vacuum target, which has yet to be observed experimentally, is possibly the most iconic process. Beyond pair-production our campaign will allow the experimental investigation of currently unexplored extreme radi… ▽ More The extreme intensities obtainable with lasers such as Gemini allow non-linear QED phenomena to be investigated according to our calculations. Electron-positron pair production from a pure vacuum target, which has yet to be observed experimentally, is possibly the most iconic process. Beyond pair-production our campaign will allow the experimental investigation of currently unexplored extreme radiation regimes, like the quantum radiation dominated regime (where quantum and self-field effects become important) and non-linear Compton scattering. This is the first experiment in a multi-part campaign proposed by a major international collaboration to investigate non-linear QED. This proposal is for the first experiment in a series of 3 to achieve our most high-profile experimental goal of pair production in vacuum, but each experiment is designed to have its own tangible high-profile outcome. △ Less

Submitted 10 March, 2021; originally announced March 2021.

Report number: Rutheford Appleton Laboratory, Central Laser Facility Proposal Reference No: HPL 112008 (2010)

A novel approach for nearly-coincident events rejection

Authors: M. Borghesi, M. De Gerone, M. Faverzani, M. Fedkevych, E. Ferri, G. Gallucci, A. Giachero, A. Nucciotti, A. Puiu

Abstract: We present a novel technique, called DSVP (Discrimination through Singular Vectors Projections), to discriminate spurious events within a dataset. The purpose of this paper is to lay down a general procedure which can be tailored for a broad variety of applications. After describing the general concept, we apply the algorithm to the problem of identifying nearly coincident events in low temperatur… ▽ More We present a novel technique, called DSVP (Discrimination through Singular Vectors Projections), to discriminate spurious events within a dataset. The purpose of this paper is to lay down a general procedure which can be tailored for a broad variety of applications. After describing the general concept, we apply the algorithm to the problem of identifying nearly coincident events in low temperature microcalorimeters in order to push the time resolution close to its intrinsic limit. In fact, from simulated datasets it was possible to achieve an effective time resolution even shorter than the sampling time of the system considered. The obtained results are contextualized in the framework of the HOLMES experiment, which aims at directly measuring the neutrino mass with the calorimetric approach, allowing to significally improve its statistical sensitivity. △ Less

Submitted 7 May, 2021; v1 submitted 7 January, 2021; originally announced January 2021.

Progress in the development of TES microcalorimeter detectors suitable for neutrino mass measurement

Authors: A. Giachero, B. Alpert, D. T. Becker, D. A. Bennett, M. Borghesi, M. De Gerone, M. Faverzani, M. Fedkevych, E. Ferri, G. Gallucci, J. D. Gard, F. Gatti, G. C. Hilton, J. A. B. Mates, A. Nucciotti, G. Pessina, A. Puiu, C. D. Reintsema, D. R. Schmidt, D. S. Swetz, J. N. Ullom, L. R. Vale

Abstract: The HOLMES experiment will perform a precise calorimetric measurement of the end point of the Electron Capture (EC) decay spectrum of 163Ho in order to extract information on neutrino mass with a sensitivity below 2 eV. In its final configuration, HOLMES will deploy 1000 detectors of low-temperature microcalorimeters with implanted 163Ho nuclei. The baseline sensors for HOLMES are Mo/Cu TESs (Tran… ▽ More The HOLMES experiment will perform a precise calorimetric measurement of the end point of the Electron Capture (EC) decay spectrum of 163Ho in order to extract information on neutrino mass with a sensitivity below 2 eV. In its final configuration, HOLMES will deploy 1000 detectors of low-temperature microcalorimeters with implanted 163Ho nuclei. The baseline sensors for HOLMES are Mo/Cu TESs (Transition Edge Sensors) on SiNx membrane with gold absorbers. Considering the large number of pixels and an event rate of about 300 Hz/pixel, a large multiplexing factor and a large bandwidth are needed. To fulfill this requirement, HOLMES will exploit recent advances in microwave multiplexing. In this contribution, we present the status of the activities in development, the performances of the developed microwave-multiplexed readout system, and the results obtained with the detectors specifically designed for HOLMES in terms of noise, time, and energy resolutions △ Less

Submitted 7 January, 2021; originally announced January 2021.

Observations of Pressure Anisotropy Effects within Semi-Collisional Magnetized-Plasma Bubbles

Authors: E. R. Tubman, A. S. Joglekar, A. F. A. Bott, M. Borghesi, B. Coleman, G. Cooper, C. N. Danson, P. Durey, J. M. Foster, P. Graham, G. Gregori, E. T. Gumbrell, M. P. Hill. T. Hodge, S. Kar, R. J. Kingham, M. Read, C. P. Ridgers, J. Skidmore, C. Spindloe, A. G. R. Thomas, P. Treadwell, S. Wilson, L. Willingale, N. C. Woolsey

Abstract: Magnetized plasma interactions are ubiquitous in astrophysical and laboratory plasmas. Various physical effects have been shown to be important within colliding plasma flows influenced by opposing magnetic fields, however, experimental verification of the mechanisms within the interaction region has remained elusive. Here we discuss a laser-plasma experiment whereby experimental results verify tha… ▽ More Magnetized plasma interactions are ubiquitous in astrophysical and laboratory plasmas. Various physical effects have been shown to be important within colliding plasma flows influenced by opposing magnetic fields, however, experimental verification of the mechanisms within the interaction region has remained elusive. Here we discuss a laser-plasma experiment whereby experimental results verify that Biermann battery generated magnetic fields are advected by Nernst flows and anisotropic pressure effects dominate these flows in a reconnection region. These fields are mapped using time-resolved proton probing in multiple directions. Various experimental, modelling and analytical techniques demonstrate the importance of anisotropic pressure in semi-collisional, high-$β$ plasmas, causing a reduction in the magnitude of the reconnecting fields when compared to resistive processes. Anisotropic pressure dynamics are crucial in collisionless plasmas, but are often neglected in collisional plasmas. We show pressure anisotropy to be essential in maintaining the interaction layer, redistributing magnetic fields even for semi-collisional, high energy density physics (HEDP) regimes △ Less

Submitted 19 October, 2020; originally announced October 2020.

The Laser-hybrid Accelerator for Radiobiological Applications

Authors: G. Aymar, T. Becker, S. Boogert, M. Borghesi, R. Bingham, C. Brenner, P. N. Burrows, T. Dascalu, O. C. Ettlinger, S. Gibson, T. Greenshaw, S. Gruber, D. Gujral, C. Hardiman, J. Hughes, W. G. Jones, K. Kirkby, A. Kurup, J-B. Lagrange, K. Long, W. Luk, J. Matheson, P. McKenna, R. Mclauchlan, Z. Najmudin , et al. (15 additional authors not shown)

Abstract: The `Laser-hybrid Accelerator for Radiobiological Applications', LhARA, is conceived as a novel, uniquely-flexible facility dedicated to the study of radiobiology. The technologies demonstrated in LhARA, which have wide application, will be developed to allow particle-beam therapy to be delivered in a completely new regime, combining a variety of ion species in a single treatment fraction and expl… ▽ More The `Laser-hybrid Accelerator for Radiobiological Applications', LhARA, is conceived as a novel, uniquely-flexible facility dedicated to the study of radiobiology. The technologies demonstrated in LhARA, which have wide application, will be developed to allow particle-beam therapy to be delivered in a completely new regime, combining a variety of ion species in a single treatment fraction and exploiting ultra-high dose rates. LhARA will be a hybrid accelerator system in which laser interactions drive the creation of a large flux of protons or light ions that are captured using a plasma (Gabor) lens and formed into a beam. The laser-driven source allows protons and ions to be captured at energies significantly above those that pertain in conventional facilities, thus evading the current space-charge limit on the instantaneous dose rate that can be delivered. The laser-hybrid approach, therefore, will allow the vast ``terra incognita'' of the radiobiology that determines the response of tissue to ionising radiation to be studied with protons and light ions using a wide variety of time structures, spectral distributions, and spatial configurations at instantaneous dose rates up to and significantly beyond the ultra-high dose-rate `FLASH' regime. It is proposed that LhARA be developed in two stages. In the first stage, a programme of in vitro radiobiology will be served with proton beams with energies between 10MeV and 15MeV. In stage two, the beam will be accelerated using a fixed-field accelerator (FFA). This will allow experiments to be carried out in vitro and in vivo with proton beam energies of up to 127MeV. In addition, ion beams with energies up to 33.4MeV per nucleon will be available for in vitro and in vivo experiments. This paper presents the conceptual design for LhARA and the R&D programme by which the LhARA consortium seeks to establish the facility. △ Less

Submitted 31 May, 2020; originally announced June 2020.

Comments: 36 pages, 11 figures, preprint submitted to Frontiers in Physics, Medical Physics and Imaging

Working principle and demonstrator of microwave-multiplexing for the HOLMES experiment microcalorimeters

Authors: D. T. Becker, D. A. Bennett, M. Biasotti, M. Borghesi, V. Ceriale, M. De Gerone, M. Faverzani, E. Ferri, J. W. Fowler, G. Gallucci, J. D. Gard, A. Giachero, J. P. Hays-Wehle, G. C. Hilton, J. A. B Mates, A. Nucciotti, A. Orlando, G. Pessina, A. Puiu, C. D. Reintsema, D. R. Schmidt, D. S. Swetz, J. N. Ullom, L. R Vale

Abstract: The determination of the neutrino mass is an open issue in modern particle physics and astrophysics. The direct mass measurement is the only theory-unrelated experimental tool capable to probe such quantity. The HOLMES experiment aims to measure the end-point energy of the electron capture (EC) decay of $^{163}$Ho with a statistical sensitivity on the neutrino mass as low as $\sim 1$ eV/c$^2$. In… ▽ More The determination of the neutrino mass is an open issue in modern particle physics and astrophysics. The direct mass measurement is the only theory-unrelated experimental tool capable to probe such quantity. The HOLMES experiment aims to measure the end-point energy of the electron capture (EC) decay of $^{163}$Ho with a statistical sensitivity on the neutrino mass as low as $\sim 1$ eV/c$^2$. In order to acquire the large needed statistics, by keeping the pile-up contribution as low as possible, 1024 transition edge sensors (TESs) with high energy and time resolutions will be employed. Microcalorimeter and bolometer arrays based on transition edge sensor with thousands of pixels are under development for several space-based and ground-based applications, including astrophysics, nuclear and particle physics, and materials science. The common necessary challenge is to develop pratical multiplexing techniques in order to simplify the cryogenics and readout systems. Despite the various multiplexing variants which are being developed have been successful, new approaches are needed to enable scaling to larger pixel counts and faster sensors, as requested for HOLMES, reducing also the cost and complexity of readout. A very novel technique that meets all of these requirements is based on superconducting microwave resonators coupled to radio-frequency Superconducting Quantum Interference Devices, in which the the changes in the TES input current is tranduced to a change in phase of a microwave signal. In this work we introduce the basics of this technique, the design and development of the first two-channel read out system and its performances with the first TES detectors specifically designed for HOLMES. In the last part we explain how to extend this approach scaling to 1024 pixels. △ Less

Submitted 11 October, 2019; originally announced October 2019.

Comments: accepted on JINST

Journal ref: JINST 14 (2019) P10035

A new energy spectrum reconstruction method for Time-Of-Flight diagnostics of high-energy laser-driven protons

Authors: G. Milluzzo, V. Scuderi, A. Alejo, A. G. Amico, N. Booth, M. Borghesi, G. A. P. Cirrone, G. Cuttone, D. Doria, J. Green, S. Kar, G. Korn, G. Larosa, R. Leanza, D. Margarone, P. Martin, P. McKenna, G. Petringa, J. Pipek, L. Romagnani, F. Romano, A. Russo, F. Schillaci

Abstract: The Time-of-Flight (ToF) technique coupled with semiconductor-like detectors, as silicon carbide and diamond, is one of the most promising diagnostic methods for high-energy, high repetition rate, laser-accelerated ions allowing a full on-line beam spectral characterization. A new analysis method for reconstructing the energy spectrum of high-energy laser-driven ion beams from TOF signals is hereb… ▽ More The Time-of-Flight (ToF) technique coupled with semiconductor-like detectors, as silicon carbide and diamond, is one of the most promising diagnostic methods for high-energy, high repetition rate, laser-accelerated ions allowing a full on-line beam spectral characterization. A new analysis method for reconstructing the energy spectrum of high-energy laser-driven ion beams from TOF signals is hereby presented and discussed. The proposed method takes into account the detector's working principle, through the accurate calculation of the energy loss in the detector active layer, using Monte Carlo simulations. The analysis method was validated against well-established diagnostics, such as the Thomson Parabola Spectrometer, during an experimental campaign carried out at the Rutherford Appleton Laboratory (RAL, UK) with the high-energy laser-driven protons accelerated by the VULCAN Petawatt laser. △ Less

Submitted 4 December, 2018; originally announced December 2018.

Control of fast electron propagation in foam target by high-Z doping

Authors: H. Xu, X. H. Yang, J. Liu, M. Borghesi

Abstract: The influence of high-Z dopant (Bromine) in low-Z foam (polystyrene) target on laser-driven fast electron propagation is studied by the 3D hybrid particle-in-cell (PIC)/fluid code HEETS.It is found that the fast electrons are better confined in doped targets due to the increasing resistivity of the target, which induces a stronger resistive magnetic field which acts to collimate the fast electron… ▽ More The influence of high-Z dopant (Bromine) in low-Z foam (polystyrene) target on laser-driven fast electron propagation is studied by the 3D hybrid particle-in-cell (PIC)/fluid code HEETS.It is found that the fast electrons are better confined in doped targets due to the increasing resistivity of the target, which induces a stronger resistive magnetic field which acts to collimate the fast electron propagation.The energy deposition of fast electrons into the background target is increased slightly in the doped target, which is beneficial for applications requiring long distance propagation of fast electrons, such as fast ignition. △ Less

Submitted 11 November, 2018; originally announced November 2018.

Expansion of a radially symmetric blast shell into a uniformly magnetized plasma

Authors: M E Dieckmann, Q Moreno, D Doria, L Romagnani, G Sarri, D Folini, R Walder, A Bret, E d'Humieres, M Borghesi

Abstract: The expansion of a thermal pressure-driven radial blast shell into a dilute ambient plasma is examined with two-dimensional PIC simulations. The purpose is to determine if laminar shocks form in a collisionless plasma that resemble their magnetohydrodynamic counterparts. The ambient plasma is composed of electrons with the temperature 2 keV and cool fully ionized nitrogen ions. It is permeated by… ▽ More The expansion of a thermal pressure-driven radial blast shell into a dilute ambient plasma is examined with two-dimensional PIC simulations. The purpose is to determine if laminar shocks form in a collisionless plasma that resemble their magnetohydrodynamic counterparts. The ambient plasma is composed of electrons with the temperature 2 keV and cool fully ionized nitrogen ions. It is permeated by a spatially uniform magnetic field. A forward shock forms between the shocked ambient medium and the pristine ambient medium, which changes from an ion acoustic one through a slow magnetosonic one to a fast magnetosonic shock with increasing shock propagation angles relative to the magnetic field. The slow magnetosonic shock that propagates obliquely to the magnetic field changes into a tangential discontinuity for a perpendicular propagation direction, which is in line with the magnetohydrodynamic model. The expulsion of the magnetic field by the expanding blast shell triggers an electron-cyclotron drift instability. △ Less

Submitted 8 May, 2018; originally announced May 2018.

Comments: 10 pages and 11 figures. Accepted for publication in the Physics of Plasmas

Ultrashort PW laser pulse interaction with target and ion acceleration

Authors: S. Ter-Avetisyan, P. K. Singh, K. F. Kakolee, H. Ahmed, T. W. Jeong, C. Scullion, P. Hadjisolomou, M. Borghesi, V. Yu. Bychenkov

Abstract: We present the experimental results on ion acceleration by petawatt femtosecond laser solid interaction and explore strategies to enhance ion energy. The irradiation of micrometer thick (0.2 - 6.0 micron) Al foils with a virtually unexplored intensity regime (8x10^19 W/cm^2 - 1x10^21 W/cm^2) resulting in ion acceleration along the rear and the front surface target normal direction is investigated.… ▽ More We present the experimental results on ion acceleration by petawatt femtosecond laser solid interaction and explore strategies to enhance ion energy. The irradiation of micrometer thick (0.2 - 6.0 micron) Al foils with a virtually unexplored intensity regime (8x10^19 W/cm^2 - 1x10^21 W/cm^2) resulting in ion acceleration along the rear and the front surface target normal direction is investigated. The maximum energy of protons and carbon ions, obtained at optimised laser intensity condition (by varying laser energy or focal spot size), exhibit a rapid intensity scaling as I^0.8 along the rear surface target normal direction and I^0.6 along the front surface target normal direction. It was found that proton energy scales much faster with laser energy rather than the laser focal spot size. Additionally, the ratio of maximum ion energy along the both directions is found to be constant for the broad range of target thickness and laser intensities. A proton flux is strongly dominated in the forward direction at relatively low laser intensities. Increasing the laser intensity results in the gradual increase in the backward proton flux and leads to almost equalisation of ion flux in both directions in the entire energy range. These experimental findings may open new perspectives for applications. △ Less

Submitted 20 March, 2018; originally announced March 2018.

Comments: 6 pages, 5 figures, 3rd EAAC workshop