Showing 1–21 of 21 results for author: Farinon, S

Towards Low-Energy Electron High-Resolution Spectroscopy with Transition-Edge Sensors

Authors: R. Ammendola, A. Apponi, G. Benato, M. G. Betti, R. Biondi, P. Bos, M. Cadeddu, A. Casale, O. Castellano, G. Cavoto, L. Cecchini, E. Celasco, M. Chirico, W. Chung, A. G. Cocco, A. P. Colijn, B. Corcione, N. D'Ambrosio, M. D'Incecco, G. De Bellis, M. De Deo, N. de Groot, A. Esposito, M. Farino, S. Farinon , et al. (40 additional authors not shown)

Abstract: We present a study of the energy resolution of transition-edge sensors (TESs) for the detection of electrons in the 100 eV kinetic energy range. The TES is a Ti-Au bilayer with an active area of $(60 \times 60)$ $μ\text{m}^2$ and a critical temperature of $\sim$ 80 mK. The electron source is based on vertically-aligned multiwall carbon nanotubes located inside the cryostat, with electrons generate… ▽ More We present a study of the energy resolution of transition-edge sensors (TESs) for the detection of electrons in the 100 eV kinetic energy range. The TES is a Ti-Au bilayer with an active area of $(60 \times 60)$ $μ\text{m}^2$ and a critical temperature of $\sim$ 80 mK. The electron source is based on vertically-aligned multiwall carbon nanotubes located inside the cryostat, with electrons generated via field emission. For electrons in the (92 - 99) eV kinetic energy range, we obtain a Gaussian energy resolution for fully-absorbed electrons of (0.479 $\pm$ 0.041 $\pm$ 0.055) eV. When considering the full-width at half-maximum of the peak, the corresponding resolution is of (1.44 $\pm$ 0.17 $\pm$ 0.27) eV. The former represents an improvement of (46 - 60)% with respect to previous results, and is mainly attributed to the reduction in the TES active area. The latter is instead an improvement of over a factor of 20, and is mainly due to the reduction in the emitting area of the electron source, which significantly suppresses electron back-scattering in proximity of the TES. These results represent a major milestone toward high-precision spectroscopy on low-energy electrons, which is a key objective for the PTOLEMY experiment. △ Less

Submitted 25 February, 2026; originally announced February 2026.

Comments: 6 pages, 4 figures

Ultra-high precision high voltage system for PTOLEMY

Authors: R. Ammendola, A. Apponi, G. Benato, M. G. Betti, R. Biondim, P. Bos, G. Cavoto, M. Cadeddu, A. Casale, O. Castellano, E. Celasco, L. Cecchini, M. Chirico, W. Chung, A. G. Cocco, A. P. Colijn, B. Corcione, N. D'Ambrosio, M. D'Incecco, G. De Bellis, M. De Deo, N. de Groot, A. Esposito, M. Farino, S. Farinon , et al. (41 additional authors not shown)

Abstract: The PTOLEMY project is prototyping a novel electromagnetic filter for high-precision $β$ spectroscopy, with the ultimate and ambitious long-term goal of detecting the cosmic neutrino background through electron capture on tritium bound to graphene. Intermediate small-scale prototypes can achieve competitive sensitivity to the effective neutrino mass, even with reduced energy resolution. To reach a… ▽ More The PTOLEMY project is prototyping a novel electromagnetic filter for high-precision $β$ spectroscopy, with the ultimate and ambitious long-term goal of detecting the cosmic neutrino background through electron capture on tritium bound to graphene. Intermediate small-scale prototypes can achieve competitive sensitivity to the effective neutrino mass, even with reduced energy resolution. To reach an energy resolution better than \SI{500}{meV} at the tritium $β$-spectrum endpoint of \SI{18.6}{keV}, and accounting for all uncertainties in the filtering chain, the electrode voltage must be controlled at the level of a few parts per million and monitored in real time. In this work, we present the first results obtained in this effort, using a chain of commercial ultra-high-precision voltage references, read out by precision multimeters and a \emph{field mill} device. The currently available precision on high voltage is, in the conservative case, as low as \SI{0.2}{ppm} per \SI{1}{kV} single board and $\lesssim$ \SI{50}{mV} over the \SI{10}{kV} series, presently limited by field mill read-out noise. However, assuming uncorrelated Gaussian noise extrapolation, the real precision could in principle be as low as \SI{0.05}{ppm} over \SI{20}{kV}. △ Less

Submitted 22 December, 2025; originally announced December 2025.

Comments: 17 pages, 13 figures

MuCol Milestone Report No. 7: Consolidated Parameters

Authors: Rebecca Taylor, Antoine Chancé, Dario Augusto Giove, Natalia Milas, Roberto Losito, Donatella Lucchesi, Chris Rogers, Lucio Rossi, Daniel Schulte, Carlotta Accettura, Simon Adrian, Rohit Agarwal, Claudia Ahdida, Chiara Aime, Avni Aksoy, Gian Luigi Alberghi, Simon Albright, Siobhan Alden, Luca Alfonso, Muhammad Ali, Anna Rita Altamura, Nicola Amapane, Kathleen Amm, David Amorim, Paolo Andreetto , et al. (437 additional authors not shown)

Abstract: This document is comprised of a collection of consolidated parameters for the key parts of the muon collider. These consolidated parameters follow on from the October 2024 Preliminary Parameters Report. Attention has been given to a high-level consistent set of baseline parameters throughout all systems of the complex, following a 10 TeV center-of-mass design. Additional details of the designs con… ▽ More This document is comprised of a collection of consolidated parameters for the key parts of the muon collider. These consolidated parameters follow on from the October 2024 Preliminary Parameters Report. Attention has been given to a high-level consistent set of baseline parameters throughout all systems of the complex, following a 10 TeV center-of-mass design. Additional details of the designs contributing to this baseline design are featured in the appendix. Likewise, explorative variations from this baseline set can be found in the appendix. The data is collected from a collaborative spreadsheet and transferred to overleaf. △ Less

Submitted 31 October, 2025; originally announced October 2025.

Future Circular Collider Feasibility Study Report: Volume 2, Accelerators, Technical Infrastructure and Safety

Authors: M. Benedikt, F. Zimmermann, B. Auchmann, W. Bartmann, J. P. Burnet, C. Carli, A. Chancé, P. Craievich, M. Giovannozzi, C. Grojean, J. Gutleber, K. Hanke, A. Henriques, P. Janot, C. Lourenço, M. Mangano, T. Otto, J. Poole, S. Rajagopalan, T. Raubenheimer, E. Todesco, L. Ulrici, T. Watson, G. Wilkinson, A. Abada , et al. (1439 additional authors not shown)

Abstract: In response to the 2020 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) Feasibility Study was launched as an international collaboration hosted by CERN. This report describes the FCC integrated programme, which consists of two stages: an electron-positron collider (FCC-ee) in the first phase, serving as a high-luminosity Higgs, top, and electroweak factory;… ▽ More In response to the 2020 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) Feasibility Study was launched as an international collaboration hosted by CERN. This report describes the FCC integrated programme, which consists of two stages: an electron-positron collider (FCC-ee) in the first phase, serving as a high-luminosity Higgs, top, and electroweak factory; followed by a proton-proton collider (FCC-hh) at the energy frontier in the second phase. FCC-ee is designed to operate at four key centre-of-mass energies: the Z pole, the WW production threshold, the ZH production peak, and the top/anti-top production threshold - delivering the highest possible luminosities to four experiments. Over 15 years of operation, FCC-ee will produce more than 6 trillion Z bosons, 200 million WW pairs, nearly 3 million Higgs bosons, and 2 million top anti-top pairs. Precise energy calibration at the Z pole and WW threshold will be achieved through frequent resonant depolarisation of pilot bunches. The sequence of operation modes remains flexible. FCC-hh will operate at a centre-of-mass energy of approximately 85 TeV - nearly an order of magnitude higher than the LHC - and is designed to deliver 5 to 10 times the integrated luminosity of the HL-LHC. Its mass reach for direct discovery extends to several tens of TeV. In addition to proton-proton collisions, FCC-hh is capable of supporting ion-ion, ion-proton, and lepton-hadron collision modes. This second volume of the Feasibility Study Report presents the complete design of the FCC-ee collider, its operation and staging strategy, the full-energy booster and injector complex, required accelerator technologies, safety concepts, and technical infrastructure. It also includes the design of the FCC-hh hadron collider, development of high-field magnets, hadron injector options, and key technical systems for FCC-hh. △ Less

Submitted 25 April, 2025; originally announced May 2025.

Comments: 627 pages. Please address any comment or request to fcc.secretariat@cern.ch

Report number: CERN-FCC-ACC-2025-0004

Future Circular Collider Feasibility Study Report: Volume 3, Civil Engineering, Implementation and Sustainability

Authors: M. Benedikt, F. Zimmermann, B. Auchmann, W. Bartmann, J. P. Burnet, C. Carli, A. Chancé, P. Craievich, M. Giovannozzi, C. Grojean, J. Gutleber, K. Hanke, A. Henriques, P. Janot, C. Lourenço, M. Mangano, T. Otto, J. Poole, S. Rajagopalan, T. Raubenheimer, E. Todesco, L. Ulrici, T. Watson, G. Wilkinson, P. Azzi , et al. (1439 additional authors not shown)

Abstract: Volume 3 of the FCC Feasibility Report presents studies related to civil engineering, the development of a project implementation scenario, and environmental and sustainability aspects. The report details the iterative improvements made to the civil engineering concepts since 2018, taking into account subsurface conditions, accelerator and experiment requirements, and territorial considerations. I… ▽ More Volume 3 of the FCC Feasibility Report presents studies related to civil engineering, the development of a project implementation scenario, and environmental and sustainability aspects. The report details the iterative improvements made to the civil engineering concepts since 2018, taking into account subsurface conditions, accelerator and experiment requirements, and territorial considerations. It outlines a technically feasible and economically viable civil engineering configuration that serves as the baseline for detailed subsurface investigations, construction design, cost estimation, and project implementation planning. Additionally, the report highlights ongoing subsurface investigations in key areas to support the development of an improved 3D subsurface model of the region. The report describes development of the project scenario based on the 'avoid-reduce-compensate' iterative optimisation approach. The reference scenario balances optimal physics performance with territorial compatibility, implementation risks, and costs. Environmental field investigations covering almost 600 hectares of terrain - including numerous urban, economic, social, and technical aspects - confirmed the project's technical feasibility and contributed to the preparation of essential input documents for the formal project authorisation phase. The summary also highlights the initiation of public dialogue as part of the authorisation process. The results of a comprehensive socio-economic impact assessment, which included significant environmental effects, are presented. Even under the most conservative and stringent conditions, a positive benefit-cost ratio for the FCC-ee is obtained. Finally, the report provides a concise summary of the studies conducted to document the current state of the environment. △ Less

Submitted 25 April, 2025; originally announced May 2025.

Comments: 357 pages. Please address any comment or request to fcc.secretariat@cern.ch

Report number: CERN-FCC-ACC-2025-0003

Future Circular Collider Feasibility Study Report: Volume 1, Physics, Experiments, Detectors

Authors: M. Benedikt, F. Zimmermann, B. Auchmann, W. Bartmann, J. P. Burnet, C. Carli, A. Chancé, P. Craievich, M. Giovannozzi, C. Grojean, J. Gutleber, K. Hanke, A. Henriques, P. Janot, C. Lourenço, M. Mangano, T. Otto, J. Poole, S. Rajagopalan, T. Raubenheimer, E. Todesco, L. Ulrici, T. Watson, G. Wilkinson, P. Azzi , et al. (1439 additional authors not shown)

Abstract: Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model.… ▽ More Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model. The report reviews the experimental opportunities offered by the staged implementation of FCC, beginning with an electron-positron collider (FCC-ee), operating at several centre-of-mass energies, followed by a hadron collider (FCC-hh). Benchmark examples are given of the expected physics performance, in terms of precision and sensitivity to new phenomena, of each collider stage. Detector requirements and conceptual designs for FCC-ee experiments are discussed, as are the specific demands that the physics programme imposes on the accelerator in the domains of the calibration of the collision energy, and the interface region between the accelerator and the detector. The report also highlights advances in detector, software and computing technologies, as well as the theoretical tools /reconstruction techniques that will enable the precision measurements and discovery potential of the FCC experimental programme. This volume reflects the outcome of a global collaborative effort involving hundreds of scientists and institutions, aided by a dedicated community-building coordination, and provides a targeted assessment of the scientific opportunities and experimental foundations of the FCC programme. △ Less

Submitted 25 April, 2025; originally announced May 2025.

Comments: 290 pages. Please address any comment or request to fcc.secretariat@cern.ch

Report number: CERN-FCC-PHYS-2025-0002

The Muon Collider

Authors: Carlotta Accettura, Simon Adrian, Rohit Agarwal, Claudia Ahdida, Chiara Aime', Avni Aksoy, Gian Luigi Alberghi, Siobhan Alden, Luca Alfonso, Muhammad Ali, Anna Rita Altamura, Nicola Amapane, Kathleen Amm, David Amorim, Paolo Andreetto, Fabio Anulli, Ludovica Aperio Bella, Rob Appleby, Artur Apresyan, Pouya Asadi, Mohammed Attia Mahmoud, Bernhard Auchmann, John Back, Anthony Badea, Kyu Jung Bae , et al. (433 additional authors not shown)

Abstract: Muons offer a unique opportunity to build a compact high-energy electroweak collider at the 10 TeV scale. A Muon Collider enables direct access to the underlying simplicity of the Standard Model and unparalleled reach beyond it. It will be a paradigm-shifting tool for particle physics representing the first collider to combine the high-energy reach of a proton collider and the high precision of an… ▽ More Muons offer a unique opportunity to build a compact high-energy electroweak collider at the 10 TeV scale. A Muon Collider enables direct access to the underlying simplicity of the Standard Model and unparalleled reach beyond it. It will be a paradigm-shifting tool for particle physics representing the first collider to combine the high-energy reach of a proton collider and the high precision of an electron-positron collider, yielding a physics potential significantly greater than the sum of its individual parts. A high-energy muon collider is the natural next step in the exploration of fundamental physics after the HL-LHC and a natural complement to a future low-energy Higgs factory. Such a facility would significantly broaden the scope of particle colliders, engaging the many frontiers of the high energy community. The last European Strategy for Particle Physics Update and later the Particle Physics Project Prioritisation Panel in the US requested a study of the muon collider, which is being carried on by the International Muon Collider Collaboration. In this comprehensive document we present the physics case, the state of the work on accelerator design and technology, and propose an R\&D project that can make the muon collider a reality. △ Less

Submitted 30 April, 2025; originally announced April 2025.

Comments: 406 pages, supplementary report to the European Strategy for Particle Physics - 2026 update

MuCol Milestone Report No. 5: Preliminary Parameters

Authors: Carlotta Accettura, Simon Adrian, Rohit Agarwal, Claudia Ahdida, Chiara Aimé, Avni Aksoy, Gian Luigi Alberghi, Siobhan Alden, Luca Alfonso, Nicola Amapane, David Amorim, Paolo Andreetto, Fabio Anulli, Rob Appleby, Artur Apresyan, Pouya Asadi, Mohammed Attia Mahmoud, Bernhard Auchmann, John Back, Anthony Badea, Kyu Jung Bae, E. J. Bahng, Lorenzo Balconi, Fabrice Balli, Laura Bandiera , et al. (369 additional authors not shown)

Abstract: This document is comprised of a collection of updated preliminary parameters for the key parts of the muon collider. The updated preliminary parameters follow on from the October 2023 Tentative Parameters Report. Particular attention has been given to regions of the facility that are believed to hold greater technical uncertainty in their design and that have a strong impact on the cost and power… ▽ More This document is comprised of a collection of updated preliminary parameters for the key parts of the muon collider. The updated preliminary parameters follow on from the October 2023 Tentative Parameters Report. Particular attention has been given to regions of the facility that are believed to hold greater technical uncertainty in their design and that have a strong impact on the cost and power consumption of the facility. The data is collected from a collaborative spreadsheet and transferred to overleaf. △ Less

Submitted 5 November, 2024; originally announced November 2024.

Interim report for the International Muon Collider Collaboration (IMCC)

Authors: C. Accettura, S. Adrian, R. Agarwal, C. Ahdida, C. Aimé, A. Aksoy, G. L. Alberghi, S. Alden, N. Amapane, D. Amorim, P. Andreetto, F. Anulli, R. Appleby, A. Apresyan, P. Asadi, M. Attia Mahmoud, B. Auchmann, J. Back, A. Badea, K. J. Bae, E. J. Bahng, L. Balconi, F. Balli, L. Bandiera, C. Barbagallo , et al. (362 additional authors not shown)

Abstract: The International Muon Collider Collaboration (IMCC) [1] was established in 2020 following the recommendations of the European Strategy for Particle Physics (ESPP) and the implementation of the European Strategy for Particle Physics-Accelerator R&D Roadmap by the Laboratory Directors Group [2], hereinafter referred to as the the European LDG roadmap. The Muon Collider Study (MuC) covers the accele… ▽ More The International Muon Collider Collaboration (IMCC) [1] was established in 2020 following the recommendations of the European Strategy for Particle Physics (ESPP) and the implementation of the European Strategy for Particle Physics-Accelerator R&D Roadmap by the Laboratory Directors Group [2], hereinafter referred to as the the European LDG roadmap. The Muon Collider Study (MuC) covers the accelerator complex, detectors and physics for a future muon collider. In 2023, European Commission support was obtained for a design study of a muon collider (MuCol) [3]. This project started on 1st March 2023, with work-packages aligned with the overall muon collider studies. In preparation of and during the 2021-22 U.S. Snowmass process, the muon collider project parameters, technical studies and physics performance studies were performed and presented in great detail. Recently, the P5 panel [4] in the U.S. recommended a muon collider R&D, proposed to join the IMCC and envisages that the U.S. should prepare to host a muon collider, calling this their "muon shot". In the past, the U.S. Muon Accelerator Programme (MAP) [5] has been instrumental in studies of concepts and technologies for a muon collider. △ Less

Submitted 28 January, 2025; v1 submitted 17 July, 2024; originally announced July 2024.

Comments: This document summarises the International Muon Collider Collaboration (IMCC) progress and status of the Muon Collider R&D programme

SPY: A Magnet System for a High-pressure Gaseous TPC Neutrino Detector

Authors: Andrea Bersani, Alan D. Bross, Michael Crisler, Stefania Farinon, Christopher Hayes, Donald Mitchell, Riccardo Musenich, Colin Narug, Jay Theilacker, Terry Tope, Erik Voirin, Vivek Jain

Abstract: We present a novel conceptual design for a magnet system that provides the magnetic field necessary for the analysis of tracks in a high-pressure gaseous argon TPC while simultaneously serving as a pressure vessel to contain the TPC gas volume. The magnet was developed within a Near Detector proposal for the Deep Underground Neutrino Experiment (DUNE). The high-pressure gaseous argon TPC is a comp… ▽ More We present a novel conceptual design for a magnet system that provides the magnetic field necessary for the analysis of tracks in a high-pressure gaseous argon TPC while simultaneously serving as a pressure vessel to contain the TPC gas volume. The magnet was developed within a Near Detector proposal for the Deep Underground Neutrino Experiment (DUNE). The high-pressure gaseous argon TPC is a component proposed to be one of the elements of an ensemble of near detectors that are needed for DUNE △ Less

Submitted 2 April, 2024; v1 submitted 27 November, 2023; originally announced November 2023.

Comments: 37 pages with 35 figures

Towards a Muon Collider

Authors: Carlotta Accettura, Dean Adams, Rohit Agarwal, Claudia Ahdida, Chiara Aimè, Nicola Amapane, David Amorim, Paolo Andreetto, Fabio Anulli, Robert Appleby, Artur Apresyan, Aram Apyan, Sergey Arsenyev, Pouya Asadi, Mohammed Attia Mahmoud, Aleksandr Azatov, John Back, Lorenzo Balconi, Laura Bandiera, Roger Barlow, Nazar Bartosik, Emanuela Barzi, Fabian Batsch, Matteo Bauce, J. Scott Berg , et al. (272 additional authors not shown)

Abstract: A muon collider would enable the big jump ahead in energy reach that is needed for a fruitful exploration of fundamental interactions. The challenges of producing muon collisions at high luminosity and 10 TeV centre of mass energy are being investigated by the recently-formed International Muon Collider Collaboration. This Review summarises the status and the recent advances on muon colliders desi… ▽ More A muon collider would enable the big jump ahead in energy reach that is needed for a fruitful exploration of fundamental interactions. The challenges of producing muon collisions at high luminosity and 10 TeV centre of mass energy are being investigated by the recently-formed International Muon Collider Collaboration. This Review summarises the status and the recent advances on muon colliders design, physics and detector studies. The aim is to provide a global perspective of the field and to outline directions for future work. △ Less

Submitted 27 November, 2023; v1 submitted 15 March, 2023; originally announced March 2023.

Comments: 118 pages, 103 figures

A Work Proposal for a Collaborative Study of Magnet Technology for a Future Muon Collider

Authors: L. Bottura, D. Aguglia, B. Auchmann, T. Arndt, J. Beard, A. Bersani, F. Boattini, M. Breschi, B. Caiffi, X. Chaud, M. Dam, F. Debray, H. De Gersem, E. De Matteis, A. Dudarev, S. Farinon, A. Kario, R. Losito, S. Mariotto, M. Mentink, R. Musenich, T. Ogitsu, M. Prioli, L. Quettier, L. Rossi , et al. (8 additional authors not shown)

Abstract: In this paper we elaborate on the nature and challenges for the magnet systems of a muon collider as presently considered within the scope of the International Muon Collider Collaboration (IMCC). We outline the structure of the work proposed over the coming period of five years to study and demonstrate relevant magnet technology. The proposal, which is part of the overall work planned to establish… ▽ More In this paper we elaborate on the nature and challenges for the magnet systems of a muon collider as presently considered within the scope of the International Muon Collider Collaboration (IMCC). We outline the structure of the work proposed over the coming period of five years to study and demonstrate relevant magnet technology. The proposal, which is part of the overall work planned to establish feasibility of a muon collider, is in direct response to the recent recommendations received from the Laboratories Directors Group (LDG). The plan is to profit from joint activities, within the scope of the IMCC and beyond, implemented through direct and EU-funded contributions. △ Less

Submitted 29 March, 2022; v1 submitted 26 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021

A Muon Collider Facility for Physics Discovery

Authors: D. Stratakis, N. Mokhov, M. Palmer, N. Pastrone, T. Raubenheimer, C. Rogers, D. Schulte, V. Shiltsev, J. Tang, A. Yamamoto, C. Aimè, M. A. Mahmoud, N. Bartosik, E. Barzi, A. Bersani, A. Bertolin, M. Bonesini, B. Caiffi, M. Casarsa, M. G. Catanesi, A. Cerri, C. Curatolo, M. Dam, H. Damerau, E. De Matteis , et al. (44 additional authors not shown)

Abstract: Muon colliders provide a unique route to deliver high energy collisions that enable discovery searches and precision measurements to extend our understanding of the fundamental laws of physics. The muon collider design aims to deliver physics reach at the highest energies with costs, power consumption and on a time scale that may prove favorable relative to other proposed facilities. In this conte… ▽ More Muon colliders provide a unique route to deliver high energy collisions that enable discovery searches and precision measurements to extend our understanding of the fundamental laws of physics. The muon collider design aims to deliver physics reach at the highest energies with costs, power consumption and on a time scale that may prove favorable relative to other proposed facilities. In this context, a new international collaboration has formed to further extend the design concepts and performance studies of such a machine. This effort is focused on delivering the elements of a $\sim$10 TeV center of mass (CM) energy design to explore the physics energy frontier. The path to such a machine may pass through lower energy options. Currently a 3 TeV CM stage is considered. Other energy stages could also be explored, e.g. an s-channel Higgs Factory operating at 125 GeV CM. We describe the status of the R&D and design effort towards such a machine and lay out a plan to bring these concepts to maturity as a tool for the high energy physics community. △ Less

Submitted 15 March, 2022; originally announced March 2022.

Comments: 23 pages, 3 figures. arXiv admin note: text overlap with arXiv:2201.07895

Magnetic design of twin aperture cos-theta superconducting dipoles with a semi-analytic approach

Authors: Alessandro Maria Ricci, Pasquale Fabbricatore, Stefania Farinon

Abstract: The magnetic design is a basic aspect of the superconducting magnets for particle accelerators. When dealing with single aperture cos-theta type dipoles, at the first order, the design can be performed with an analytic approach based on a sector dipole approximation followed by a numerical optimization. For double aperture dipoles the magnetic cross-talk between apertures makes this approach unfea… ▽ More The magnetic design is a basic aspect of the superconducting magnets for particle accelerators. When dealing with single aperture cos-theta type dipoles, at the first order, the design can be performed with an analytic approach based on a sector dipole approximation followed by a numerical optimization. For double aperture dipoles the magnetic cross-talk between apertures makes this approach unfeasible. We have developed a semi-analytic model, which starting from a sector dipole approximation, allows to consider the cross-talk between the two apertures. We also demonstrate that the iron yoke contribution to harmonics, although dominant, does not change the optimal configuration found in its absence. As examples, we show two possible electromagnetic designs for the D2 dipole of the High Luminosity upgrade of LHC. The semi-analytic model can be generalized to a larger class of magnets. △ Less

Submitted 6 February, 2019; originally announced February 2019.

Comments: 7 pages, 8 figures

Magnetic coupling to the Advanced Virgo payloads and its impact on the low frequency sensitivity

Authors: A. Cirone, A. Chincarini, M. Neri, S. Farinon, G. Gemme, I. Fiori, F. Paoletti, E. Majorana, P. Puppo, P. Rapagnani, P. Ruggi, B. L. Swinkels

Abstract: We study the electromagnetic coupling of the Advanced Virgo (AdV) Input Mirror Payload (IMP) in response to a slowly time-varying magnetic field. As the problem is not amenable to analytical solution, we employ and validate a finite element (FE) analysis approach. The FE model is built to represent as faithfully as possible the real object and it has been validated by comparison with experimental… ▽ More We study the electromagnetic coupling of the Advanced Virgo (AdV) Input Mirror Payload (IMP) in response to a slowly time-varying magnetic field. As the problem is not amenable to analytical solution, we employ and validate a finite element (FE) analysis approach. The FE model is built to represent as faithfully as possible the real object and it has been validated by comparison with experimental measurements. The intent is to estimate the induced currents and the magnetic field in the neighbourhood of the payload. The procedure found 21 equivalent electrical configurations that are compatible with the measurements. These have been used to compute the magnetic noise contribution to the total AdV strain noise. At the current stage of development AdV seems to be unaffected by magnetic noise, but we foresee a non-negligible coupling once AdV reaches the design sensitivity. △ Less

Submitted 23 October, 2018; v1 submitted 17 July, 2018; originally announced July 2018.

Comments: 8 pages, 8 figures, 2 tables

Insertion Magnets

Authors: G. Ambrosio, M. Anerella, R. Bossert, D. Cheng, G. Chlachidze, D. Dietderich, D Duarte Ramos, P. Fabbricatore, S. Farinon, H. Felice, P. Ferracin, P. Fessia, J. Garcia Matos, A. Ghosh, P. Hagen, S. Izquierdo Bermudez, M. Juchno, S. Krave, M. Marchevsky, T. Nakamoto, T. Ogitsu, J. C. Perez, H. Prin, J. M. Rifflet, G. L. Sabbi , et al. (12 additional authors not shown)

Abstract: Chapter 3 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temper… ▽ More Chapter 3 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report. The Large Hadron Collider (LHC) is one of the largest scientific instruments ever built. Since opening up a new energy frontier for exploration in 2010, it has gathered a global user community of about 7,000 scientists working in fundamental particle physics and the physics of hadronic matter at extreme temperature and density. To sustain and extend its discovery potential, the LHC will need a major upgrade in the 2020s. This will increase its luminosity (rate of collisions) by a factor of five beyond the original design value and the integrated luminosity (total collisions created) by a factor ten. The LHC is already a highly complex and exquisitely optimised machine so this upgrade must be carefully conceived and will require about ten years to implement. The new configuration, known as High Luminosity LHC (HL-LHC), will rely on a number of key innovations that push accelerator technology beyond its present limits. Among these are cutting-edge 11-12 tesla superconducting magnets, compact superconducting cavities for beam rotation with ultra-precise phase control, new technology and physical processes for beam collimation and 300 metre-long high-power superconducting links with negligible energy dissipation. The present document describes the technologies and components that will be used to realise the project and is intended to serve as the basis for the detailed engineering design of HL-LHC. △ Less

Submitted 26 May, 2017; originally announced May 2017.

Comments: 19 pages, Chapter 3 in High-Luminosity Large Hadron Collider (HL-LHC) : Preliminary Design Report

Journal ref: CERN Yellow Report CERN 2015-005, pp. 61-79

Mu2e Technical Design Report

Authors: L. Bartoszek, E. Barnes, J. P. Miller, J. Mott, A. Palladino, J. Quirk, B. L. Roberts, J. Crnkovic, V. Polychronakos, V. Tishchenko, P. Yamin, C. -h. Cheng, B. Echenard, K. Flood, D. G. Hitlin, J. H. Kim, T. S. Miyashita, F. C. Porter, M. Röhrken, J. Trevor, R. -Y. Zhu, E. Heckmaier, T. I. Kang, G. Lim, W. Molzon , et al. (238 additional authors not shown)

Abstract: The Mu2e experiment at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the L… ▽ More The Mu2e experiment at Fermilab will search for charged lepton flavor violation via the coherent conversion process mu- N --> e- N with a sensitivity approximately four orders of magnitude better than the current world's best limits for this process. The experiment's sensitivity offers discovery potential over a wide array of new physics models and probes mass scales well beyond the reach of the LHC. We describe herein the preliminary design of the proposed Mu2e experiment. This document was created in partial fulfillment of the requirements necessary to obtain DOE CD-2 approval. △ Less

Submitted 16 March, 2015; v1 submitted 21 January, 2015; originally announced January 2015.

Comments: compressed file, 888 pages, 621 figures, 126 tables; full resolution available at http://mu2e.fnal.gov; corrected typo in background summary, Table 3.4

Report number: Fermilab-TM-2594 , Fermilab-DESIGN-2014-1

Advanced Virgo: a 2nd generation interferometric gravitational wave detector

Authors: F. Acernese, M. Agathos, K. Agatsuma, D. Aisa, N. Allemandou, A. Allocca, J. Amarni, P. Astone, G. Balestri, G. Ballardin, F. Barone, J. -P. Baronick, M. Barsuglia, A. Basti, F. Basti, Th. S. Bauer, V. Bavigadda, M. Bejger, M. G. Beker, C. Belczynski, D. Bersanetti, A. Bertolini, M. Bitossi, M. A. Bizouard, S. Bloemen , et al. (209 additional authors not shown)

Abstract: Advanced Virgo is the project to upgrade the Virgo interferometric detector of gravitational waves, with the aim of increasing the number of observable galaxies (and thus the detection rate) by three orders of magnitude. The project is now in an advanced construction phase and the assembly and integration will be completed by the end of 2015. Advanced Virgo will be part of a network with the two A… ▽ More Advanced Virgo is the project to upgrade the Virgo interferometric detector of gravitational waves, with the aim of increasing the number of observable galaxies (and thus the detection rate) by three orders of magnitude. The project is now in an advanced construction phase and the assembly and integration will be completed by the end of 2015. Advanced Virgo will be part of a network with the two Advanced LIGO detectors in the US and GEO HF in Germany, with the goal of contributing to the early detections of gravitational waves and to opening a new observation window on the universe. In this paper we describe the main features of the Advanced Virgo detector and outline the status of the construction. △ Less

Submitted 16 October, 2014; v1 submitted 18 August, 2014; originally announced August 2014.

Comments: Submitted to Classical and Quantum Gravity. 55 pages, 29 figures

Journal ref: Class. Quantum Grav. 32 (2015) 024001

Reconstruction of the gravitational wave signal $h(t)$ during the Virgo science runs and independent validation with a photon calibrator

Authors: Virgo collaboration, T. Accadia, F. Acernese, M. Agathos, A. Allocca, P. Astone, G. Ballardin, F. Barone, M. Barsuglia, A. Basti, Th. S. Bauer, M. Bejger, M . G. Beker, C. Belczynski, D. Bersanetti, A. Bertolini, M. Bitossi, M. A. Bizouard, M. Blom, M. Boer, F. Bondu, L. Bonelli, R. Bonnand, V. Boschi, L. Bosi , et al. (171 additional authors not shown)

Abstract: The Virgo detector is a kilometer-scale interferometer for gravitational wave detection located near Pisa (Italy). About 13 months of data were accumulated during four science runs (VSR1, VSR2, VSR3 and VSR4) between May 2007 and September 2011, with increasing sensitivity. In this paper, the method used to reconstruct, in the range 10 Hz-10 kHz, the gravitational wave strain time series $h(t)$… ▽ More The Virgo detector is a kilometer-scale interferometer for gravitational wave detection located near Pisa (Italy). About 13 months of data were accumulated during four science runs (VSR1, VSR2, VSR3 and VSR4) between May 2007 and September 2011, with increasing sensitivity. In this paper, the method used to reconstruct, in the range 10 Hz-10 kHz, the gravitational wave strain time series $h(t)$ from the detector signals is described. The standard consistency checks of the reconstruction are discussed and used to estimate the systematic uncertainties of the $h(t)$ signal as a function of frequency. Finally, an independent setup, the photon calibrator, is described and used to validate the reconstructed $h(t)$ signal and the associated uncertainties. The uncertainties of the $h(t)$ time series are estimated to be 8% in amplitude. The uncertainty of the phase of $h(t)$ is 50 mrad at 10 Hz with a frequency dependence following a delay of 8 $μ$s at high frequency. A bias lower than $4\,\mathrm{μs}$ and depending on the sky direction of the GW is also present. △ Less

Submitted 3 July, 2014; v1 submitted 23 January, 2014; originally announced January 2014.

Comments: 35 pages, 16 figures. Accepted by CQG

Journal ref: T Accadia et al 2014 Class. Quantum Grav. 31 165013

Status of the Super-B factory Design

Authors: W. Wittmer, K. Bertsche, A. Chao, A. Novokhatski, Y. Nosochkov, J. Seeman, M. K. Sullivan, U. Wienands, S. Weathersby, A. V. Bogomyagkov, E. Levichev, S. Nikitin, P. Piminov, D. Shatilov, S. Sinyatkin, P. Vobly, I. N. Okunev, B. Bolzon, L. Brunetti, A. Jeremie, M. E. Biagini, R. Boni, M. Boscolo, T. Demma, A. Drago , et al. (20 additional authors not shown)

Abstract: The SuperB international team continues to optimize the design of an electron-positron collider, which will allow the enhanced study of the origins of flavor physics. The project combines the best features of a linear collider (high single-collision luminosity) and a storage-ring collider (high repetition rate), bringing together all accelerator physics aspects to make a very high luminosity of 10… ▽ More The SuperB international team continues to optimize the design of an electron-positron collider, which will allow the enhanced study of the origins of flavor physics. The project combines the best features of a linear collider (high single-collision luminosity) and a storage-ring collider (high repetition rate), bringing together all accelerator physics aspects to make a very high luminosity of 10$^{36}$ cm$^{-2}$ sec$^{-1}$. This asymmetric-energy collider with a polarized electron beam will produce hundreds of millions of B-mesons at the $Υ$(4S) resonance. The present design is based on extremely low emittance beams colliding at a large Piwinski angle to allow very low $β_y^\star$ without the need for ultra short bunches. Use of crab-waist sextupoles will enhance the luminosity, suppressing dangerous resonances and allowing for a higher beam-beam parameter. The project has flexible beam parameters, improved dynamic aperture, and spin-rotators in the Low Energy Ring for longitudinal polarization of the electron beam at the Interaction Point. Optimized for best colliding-beam performance, the facility may also provide high-brightness photon beams for synchrotron radiation applications. △ Less

Submitted 9 October, 2011; originally announced October 2011.

3D Magnetic Analysis of the CMS Magnet

Authors: V. I. Klyukhin, D. Campi, B. Curé, A. Desirelli, S. Farinon, H. Gerwig, D. Green, J. P. Grillet, A. Hervé, F. Kircher, B. Levesy, R. Loveless, R. P. Smith

Abstract: The CMS magnetic system consists of a super-conducting solenoid coil, 12.5 m long and 6 m free bore diameter, and of an iron flux-return yoke, which includes the central barrel, two end-caps and the ferromagnetic parts of the hadronic forward calorimeter. The magnetic flux density in the center of the solenoid is 4 T. To carry out the magnetic analysis of the CMS magnetic system, several 3D models… ▽ More The CMS magnetic system consists of a super-conducting solenoid coil, 12.5 m long and 6 m free bore diameter, and of an iron flux-return yoke, which includes the central barrel, two end-caps and the ferromagnetic parts of the hadronic forward calorimeter. The magnetic flux density in the center of the solenoid is 4 T. To carry out the magnetic analysis of the CMS magnetic system, several 3D models were developed to perform magnetic field and force calculations using the Vector Fields code TOSCA. The analysis includes a study of the general field behavior, the calculation of the forces on the coil generated by small axial, radial displacements and angular tilts, the calculation of the forces on the ferromagnetic parts, the calculation of the fringe field outside the magnetic system, and a study of the field level in the chimneys for the current leads and the cryogenic lines. A procedure to reconstruct the field inside a cylindrical volume starting from the values of the magnetic flux density on the cylinder surface is considered. Special TOSCA-GEANT interface tools have being developed to input the calculated magnetic field into the detector simulation package. △ Less

Submitted 29 September, 2011; originally announced September 2011.

Comments: 4 pages, 6 figures, 1 equation, 14 references

Journal ref: IEEE Transaction on Applied Superconductivity, v. 10, no. 1, pp. 428-431, March 2000